(800) 853-2651
SHOP NOW

Recent content by rabrac

Yesterday's Tractor Forums
  1. R

    John Deere thrashing machine

    Gerald, I didn't recollect correctly the thresher doesn't have spoke rims it's actually more of a spoke type hub that the rim is fastened to. Here's a picture of it so now you can take a look at it. My father said that these were the original rims that came on it when my grandfather purchased it.
  2. R

    ‘64 4020D Syncro Hydraulics

    Okay sorry I could remember if the 20 series were set up with the hex shaft or if that was the 30 series. Been a few years since I worked on a 4020. Thanks for the update.
  3. R

    3020 only steering and brakes

    De-stroke the main pump and then try it again. The priority valve could be causing the problem and yes you should have steering & brakes that is the safety feature of the priority valve. Make sure the transmission pump is supplying good flow of oil to the front main pump.
  4. R

    ‘64 4020D Syncro Hydraulics

    Did you check out the transmission pump located in the differential housing and the sump screen located below. The other thing that could be causing loss of hydraulic pressure is that the main front pump needs to be de-stroked there maybe a piece of debris caught in one of the valves on that...
  5. R

    John Deere thrashing machine

    I have my grandfather's John Deere thrashing machine. I think it was built in the late 1940's. It's painted the traditional green and yellow, but the only serial tag that I found on it says it was manufactured by the Hart Carter Company of Peoria, Illinois. The serial number is H51865. I would...
  6. R

    John Deere 4400 Left Brake removal

    I realize you asked this question awhile ago, but the drum assembly has a removeable metal cap on the face of the drum. When you remove it and also remove the drive shaft to the final drive. Then you can turn the drum and look through the hole where the cap was located and you will see the bolts...
  7. R

    IH 574 tractor 200c gas engine

    Thanks for the advise I went back online and found TractorJoe had the .040 oversized rings available. Got them order and should have them next week.
  8. R

    IH 574 tractor 200c gas engine

    I'm in the process of overhauling this engine. Had to have the block bored .040 on the cylinders. I ordered a engine overhaul kit when I received it the .040 oversized pistons arrived with no rings. I've since then been desperately looking for a set of oversize rings for these 4 pistons. I would...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top