(800) 853-2651
SHOP NOW

Recent content by RBoots

Yesterday's Tractor Forums
  1. R

    300 U hydraulic DEAD ?

    There is a suction screen under that top reservoir/ cover that is quite fine and are prone to plug up. Ross
  2. R

    1850 Gasser won't start or backfires through the carb when it does.

    I don't remember which one, but I looked up which Zenith carbs that would fit it, and this was the list I came up with:Zenith 13209, 13638, 13750, 14990, 15099. I found a surplus or NOS actual Zenith on ebay for like $150 after watching for a bit. Also, is this the carb you have? Apparently...
  3. R

    Super 55 salvage

    Hey Randy! Been VEEEEERY busy! I'm working on more stuff than ever for other people it seems, while also working my regular job, and driving truck for another fellow on many weekends of the summer. Had a couple accidents the last couple years in a row that really slowed me down but, overall...
  4. R

    2404 rear end compatibility

    Thank you for the information guys! That will save me a bunch of digging around chasing empty leads!
  5. R

    Super 55 salvage

    Didn't Kent say he sold his inventory to All States Ag?
  6. R

    1850 Gasser won't start or backfires through the carb when it does.

    Is that a Holley carb? If so they have an accelerator pump type of deal inside them that wears out the bore and they'll never run right. You can adjust them to run wide open, or at an idle, but not both. Had that happen with many Holley equipped tractors, Ford, Allis, Oliver. I tossed the one on...
  7. R

    2404 rear end compatibility

    Hey guys, I'm looking at a decent 2404 that a friend has for sale. It has a broken rear end housing that isn't repairable. I'm wondering if anyone would know what, if any other IH rear ends would fit on that tractor? I know where there is a 2414 or 2424, but it's a good distance away and I can't...
  8. Oliver/Cletrac OC3-HG undercarriage and misc parts

    For sale Oliver/Cletrac OC3-HG undercarriage and misc parts

    I have for an Oliver OC3 or Cletrac HG 2 good front idlers, 1 final drive for parts with good sprocket, 1 bellhousing with driveshaft, 1 drawbar support, 1 clutch pedal, 1 track frame pivot / mounting bracket, and 2 complete tracks. The tracks are in overall good shape, links are decent, as are...
    $400.00
  9. Oliver Super 55 grille panels
    Expired

    For sale Oliver Super 55 grille panels

    1 set of Super 55 grille pieces. Need some work, but very usable as they are. No center strip. I'm asking $85 + shipping for then 989 292 9688
    $85.00
  10. R

    Does anyone know what this thing is?

    At the local scrapyard a couple days ago and saw this old steel wheeled implement. It has a hopper and some flexible tubes, with some sort of a ground driven pump, and even has "wings" for wider application of whatever it does. Maybe for application of powder insecticides or lime / gypsum? They...
  11. R

    IH 574 Gas - Popping Under Load - At my wit's end

    Does yours still have the fuel shut off solenoid intact? My 674 did. It was doing similar to yours and I took an adjustable main jet from an Oliver Super 88 I had and stuck in there. It ran great! So I ordered a new shut off solenoid, (and the jet that goes inside it that is sold separately) for...
  12. R

    530CK gas engine won't stay running

    Hit it with carb clean while it's running,if it smooths out its fuel related. If not, it's probably the condensor. As the other poster said, you can't get a good condensor anymore. I've replaced more new condensors within a year than I ever have an old one. If you're ever going to do a tune up...
  13. R

    Ferguson 40 bevel pinion

    Well the ring gear on these is very solid, the teeth on the pinion, not so much. The ring gear is perfectly fine, the leading edge of the pinion shaft teeth are chipped off on one tooth. I know they have to be a matched set, but I bought a set out of what was supposed to be a 50, and the pinion...
  14. R

    Ferguson 40 bevel pinion

    Thank you PT farmer! Those are the numbers I was looking for!
  15. R

    Ferguson 40 bevel pinion

    Hello everyone, I have been been trying to find a bevel pinion shaft for a Ferguson 40 tractor. This isn't the industrial tractor, but the red and cream row crop type tractor. The pinion I have had a pin run through it, and while the ring gear is good, the pinion is toast. I know these tractors...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top