(800) 853-2651
SHOP NOW

Recent content by red guy

Yesterday's Tractor Forums
  1. R

    Installing C281 power unit motor in a M

    Thanks everyone for the information, I Should have everything needed from a M to complete the swap.
  2. R

    Installing C281 power unit motor in a M

    Will a C281 motor from a power unit bolt right into a M? Concerned if there is any issues with crankshaft, flywheel, or whatever else I am not thinking of?
  3. R

    tunica,ms

    I pull against Bill every summer, he is that good. Congratulations Bill
  4. R

    50 pound IH profile weights

    where are you located Curt?
  5. R

    LP Manifold

    Anything wrong with LP manifold for Farmall M from Dennys Carb Shop. Seems to be the cheapest I could find. I know stay away but there probably all casted in the same place.
  6. R

    Leroy

    Previous owner of my M had the same thing happen, I found one of the teeth on the shaft had a big chunk out of it. Not much room for the balls to get out. Got to love putting those $100.00 bearings in.
  7. R

    M transmission

    Super M has a faster transmission. You can swap them back and forth, the pinion shafts should be the same. Just make sure you match the gears top and bottom. 3rd gear in super is a tad bit slower than 4th gear in a "M.
  8. R

    Oliver Super 99

    Had a guy tell me they heard someone was running over 200lbs, seems like a lot. I wanted to try around 100, but didn't know what the system could handle. Isn't there a built in relief valve that you would have to modify to raise the pressure?
  9. R

    Oliver Super 99

    How do you raise fuel pressure on a Oliver Super 99? And how much is to much?
  10. R

    Freeburg IL Pull

    Good pull, lots of spectators. But,please pull North to South next year. Better dirt on that end of track. If you rope off North end of track tractors could stage there.
  11. R

    MW 9 speed

    It will work, did it to mine. The hub on the band brake rotor is the same size outer diameter as the sleve on the disk brakes that slides on the bull pinion, so so as long as your seals are good you just swap parts. Those disk brakes are heavy.
  12. R

    Freeburg Tractor Pull

    Had lots of fun, been pulling there for years. The track was the best one I have seen there. Would be nice if you would change the 6500lb 6mph to a 6000lb class. I think you only had one hook in the 6500lb. You might get a few more to pull 6000lb. Going from 5500lb to 6500lb scares people...
  13. J

    Oil Pump Gasket

    Stupid question: do (internally-mounted) oil pumps require gaskets? Specifically on C200 gas engines?
  14. R

    tire mounting on aluminum rims

    easiest tires I ever mounted. The tire fell into place didn't even hardly need a bar. I had to put silicon on screws that I ran into the bead, very small leak there when I checked with soap water
  15. R

    Waterloo IL Pull

    Good pull hope they have it again next year
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top