(800) 853-2651
SHOP NOW

Recent content by Reddog

Yesterday's Tractor Forums
  1. N

    John Deere 4240 / 4440 cylinder head interchange?

    John Deere 4240 engine rebuilt 1 year ago (sleeves, pistons, bearings, Injection Pump, head). Had it on the Dyno last year and it was pushing 135HP at 540 RPM s. The head is cracked and leaking coolant now. There has also been a turbo on this tractor for 5+ years. At this point, should I...
  2. 3

    1973 Gravely 812 charging system problems

    This is a reply to an archived post by SteveAdvance on January 28, 2014 at 21:11:09. https://www.yesterdaystractors.com/cgi-bin/viewit.cgi?bd=gardent&th=120703 Original subject was "Re: 1973 Gravely 812 charging system problems". I know this was is an old post but... Thank You for making...
  3. Dennis P

    clutch in a KT

    I know the flywheel & clutch are different than later, but will the over-center assembly work? the clutch will disengage while traveling & you have to hold the clutch lever in all the time. The original is really worn & want to replace with later style. Thanks!
  4. L

    Super 99

    Does anyone have the number of the coupling chain for the super 99 transmisson?
  5. A

    MF 30 hydraulic pump drive shaft coupler removal

    Can anybody advice me on the following: How is the coupler attached to the drive shaft How to set about replacing the coupler
  6. M

    720 730 standard

    does anyone have any info on how many standards came with a 3 point?
  7. F

    Owen Aaland - Pressure Plate Fingers?

    Would you please give more information on pressure plate finger adjustment? I don't understand. If I have been doing it wrong, I sure want to do it right. Thanks.
  8. B

    Clutch problem on Late B

    Clutch started slipping BAD today while spreading walnut hulls with my old JD spreader. Took off cover on pulley and one of the adjusting bolts was broken clean off. Is that a stud or a special bolt and who would have those? I need to get this old girl going quick! It has a job to do!
  9. A

    Glennster or other bodymen

    I'm repairing 6 inch long 1/4 to 1/2 inch deep gouge in my wife's minivan. Some of the damage is on the sliding door. Is the SEM panel adhesive best for this or is it overkill? What would you use and how would you prep it? Thanks for your time.
  10. H

    Briggs and Stratton engine

    Any one here know of an old B&S model KK? 10 horse approximately 1957-58. Also where to get parts???Thanks Henry
  11. M

    Case tachometer

    We are looking for a new tachometer to fit a 930 CAse tractor and haven't been looking in the right places I guess, any out there? John Saeli, I saw you responding to some messages and was reminded that I've gotten some fine parts and info from you in the past, do you know of any? Thanks.
  12. V

    Dutchman

    Mark, Just checking to see if you recieved the photos and check. Jerry from Ohio
  13. M

    lowspeedlife are you there?

    I see an older post about an ixlb engine. Do you still have it?
  14. A

    massey 3165 shift fork broke

    there are two large springs for the shift lever none were on my machine one was broke in the gearbox with the shift lever spring . where do the large springs go the parts book shows them under the rubber boot which makes no sense......thanks bill
  15. B

    jd 50 loader

    does anyone know if the rear right and left mounting brackets are the same i only have the right one.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top