(800) 853-2651
SHOP NOW

Recent content by relink

Yesterday's Tractor Forums
  1. R

    Oliver 1650

    Thank you for the info on the pin size. Much appreciated! I thought about loading the tires but I only need the extra weight 5% of the time. This way I can work in the yard with the tractor without the extra weight and not rut my yard up.
  2. R

    Oliver 1650

    I am building a weight box to hook up to the 3 point on my 1650. I want to run a solid rod thru the center of the box and then fill with concrete. Should I use a 1? solid rod?
  3. R

    1650 Rear weights

    Will rear wheel weights off a 2 digit and 3 digit series bolt up to a 1650?
  4. R

    1650 stack weights

    So this time I just use 1 long bolt to hold them on and if I should add more weights in the future I can use the other hole with a longer bolt. Correct?
  5. R

    1650 stack weights

    I have a 1650 with the starter weight already on it and I just purchased 2 more stack weights for it. My question is how do I bolt the 2 new stack weights to the starter weight?
  6. R

    front end swap on 1650

    How long should it take to do the complete swap from narrow to wide front?
  7. R

    front end swap on 1650

    No not at this time.
  8. R

    front end swap on 1650

    Going to switch out a narrow front for a wide front. My question is when I have the front end off should I replace anything while the tractor is a part? Recommendations?
  9. R

    Row Crop 66

    I am not positive that is the problem. Is it as simple as pulling out the PTO shaft from the rear end to verify?
  10. R

    Row Crop 66

    How hard is it to replace?
  11. R

    Row Crop 66

    Anyone ever snap the PTO shaft on a 66?
  12. R

    John Deere running gear

    Thank you very much for the info. Much appreciated.
  13. R

    John Deere running gear

    Ok, I just found out the running gear is a JD 1065. My next question is what is the weight capacity for this unit? I want to put a 1500 gal water tank on it which puts me at 1200lbs. Will it handle it?
  14. R

    John Deere running gear

    I will try and get a picture loaded up tonight.
  15. R

    John Deere running gear

    How can I tell what model JD running gear I have if the model plate is missing? The hubs are 6 lug if that helps.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top