(800) 853-2651
SHOP NOW

Recent content by RenegadeRick

Yesterday's Tractor Forums
  1. A

    need standard

    who would have a set or a single standard piston they would sell dropped a valve in one of mine thanks
  2. C

    weak spark

    I JUST GOT A SIMPLICITY MODEL V WALK BEHIND 5 H.P. BRIGGS THAT HAS BEEN CONVERTED TO ELECTRONIC IGNITION BUT IT HAS A WEAK SPARK, I DON'T HAVE ANY EXPERIENCE WITH THESE ELECTRONIC UNITS. IS THERE ANYTHING THAT I NEED TO DO OR CHECK?,
  3. R

    9N input shaft gasket

    Thanks ,Guys For the N-put on the input gasket !!! RR
  4. R

    Happy New Year!

    HAPPY NEW YEAR TO YOUALL !!!!!!!!!!! RenegadeRick,in Texas
  5. R

    Had to fabricate plate for 9N engine to fit my motorstand !

    Well i thought i had it made bought a 2 ton folding engine hoist on sale from TSC.Went and got my old engine stand that had been loaned out several yrs only to find it wouldnt fit my eng any way you adj it. So i traced outline of houseing on cardboard took it to the shop cut out steel plate cut...
  6. R

    Merry Christmas

    Wishing everyone a VERY MERRY CHRISTMAS From ,Texas
  7. R

    Trans seal PTO seal 1941 9N NAPA parts #s

    Thanks ,Den I appreciate the information. Merry Christmas & Happy New Years to you and your family Rick
  8. R

    Trans seal PTO seal 1941 9N NAPA parts #s

    Any body happen to know the Napa parts #s for 1941 9N trans seal & Pto seal ???? Thanks ,Rick
  9. R

    Wire retaining clip found in bottom of tranny bell houseing

    Thanks ,Brian You could be right.It might have come off my existing starter drive it has been acting up lately !!
  10. R

    Wire retaining clip found in bottom of tranny bell houseing

    Pulled motor off 41 9N today getting ready to rebuld.Found whats left of a wire retaining clip in the bottom of trans bellhouseing about the size of a quarter.Anybody got any idea where this could have come from ???????????
  11. R

    Winter is here

    Yep it is,was sanding and paintin on the old 9n yeaterday close to 80 degree today sittin on 30 degree here in Central Texas BRRRRRRRR !!!!!!!!
  12. R

    tire question

    Polyurethane foam but its pretty pricey.We have it done on the tractors at work.A place called Stanley Industrial Tires in Gladewater,Tx
  13. R

    Idiot light wireing

    Yeah i took the one wire off it was fried and put a threee wire on it and rewired for it.Just makeing sure i got the idiot light wired in right before i fired it up. Thanks RenegadeRick
  14. R

    Idiot light wireing

    Thanks ,JMOR Sounds good to me.Someone had changed over to 12v one wire system and used 110v house wire for wireing. Had a push pull switch instead of key switch so im redoing all this mess so i know what is what !!!!!!!
  15. R

    Idiot light wireing

    Im hooking up a Gm three wire alt and useing a two wire idiot light like the ones used on a truck pto to tell you when its engaged. My question is one side has to be grounded to work right? Or somehow does it work with both wires hooked into the dist side of the ballast resistor ?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top