(800) 853-2651
SHOP NOW

Recent content by Ric Ks,

Yesterday's Tractor Forums
  1. R

    KBA ...unworn original..

    Remember seeing a older farmer on the Marais des Cygnes River bottoms 35 years back, looked more like a 16 or 18 footer and walking the dog with an early 50's G. A few days earlier he was plowing the same field with the same tractor with a 4 bottom plow. Maybe good sandy soil?? Ric.
  2. R

    found under the work bench

    Leroy; I checked they are right handed ok but not knowing how to measure for sure I layed them on a 2x10 with the shin lined up with the edge then went down the plank until across from the tail edge and measured across the plank at the furtherest part of the cutting edge. Measures just over...
  3. R

    Vemeer 604j Baler

    Dont know why it was omitted from your manual. Mine shows hydrolic, electric, and netrap. If I have a bale sitting in the chamber, I dont dare run the twine tubes in and out as they will catch on the belts or something and bend them. If its turning ok but if I stop to rethread or something I...
  4. R

    found under the work bench

    Farmallb: I was raised on a farm 6 mi N/E of Holton and now live 1 mile further east. I've been going to ask you to post pictures of you CC, as dad owned one in the late 40s. I never saw it for I was born in 54 and I think dad traded it for a WD in 51. I've looked at a lot of tractor gatherings...
  5. R

    found under the work bench

    Gee I'll have to check. I didnt even think about left or right and didnt check. I think they do throw to the right, though now you make me wonder. Gives me a reason to go to the barn after services tomorrow and see. Ric.
  6. R

    New Plow shares for IH #8 and JD #44

    I didn't read your post untill I posted above. I dont know if they are what you want but I bet they will fit. See "under the work bench." Ric
  7. R

    found under the work bench

    While cleaning out a shed on an old farm stead, I found, along with some other things, two JD plow shares. I measured them as 14 inches and they have never been in the ground after they were repointed. They have had new points welded on them and they look like new. They have one mounting bolt...
  8. R

    What Do You Think of This Gooseneck Trailer? (PICS)

    Maybe the angle of the photo but looks like to me the axels are way back there, putting more waight on the truck than should be? I do like the location of the jacks on the front better that the one I worked on friday. His were welded to the front of the bed with no bracing to the frame. He...
  9. R

    Be safe! Be smart! Be Careful

    Some times we want the children to have fun so badly that we dont think things thru carefully. You have to remember that the portion of the brain that ties consequences to actions is not fully developed until the age of twenty. She may have seen you move the lever but couldnt comprehend the...
  10. R

    ot basment

    please be carefull. OSHA would shut you down in a wink of an eye if they knew you didnt have shoring on that dirt. I know it is most likely vergin and wont move under normal conditions but. Id spend no time down there with out a ladder within arms reach and that may not be enough if things shift.
  11. R

    Can I JB Weld this?

    Are manifolds still pot mettal or they some kind of ceramic?? I wonder if they are cast steal anc can you wire weld it temporary at least. we used to braze them with some success.
  12. R

    Just Pickup Allis WD45

    WHAT???? No tool/grease gun box. No crank holder bracket. I bet you didnt even get the crank!! And that looks like the wrong seat! Man did you get ripped,, Bring it on over to my place while its still loaded up and I'll give you 800.00 for it so you wont have to feel so bad. Some guys just dont...
  13. R

    OT. Feds raid Gibson guitar factories

    If thats the case how come these landscape shows on TV the wife loves to watch, have exotic plants from Africa and other places. I think maybe thats where we get these unusual weeds now.
  14. R

    (OT) Think I'm gonna be sick #2...

    Guy I worked with was on a service call. As he was leaving the lady's cat ran under van and was hit. Lady went off on him and ended with "she is a mother with 3 kittens, what am I supposed to do now"? He told her,"I'll drive around the block a few times, send em out one at a time!" Same guy...
  15. R

    Tractor show in Hoyt Kansas

    KS 75 hwy about 11 mi. north of the capital city, Think its Hwy 214 east to town. Or county road 110, which ever.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top