-
R
power steering problems/630
Helping a freind with his newly aquired tractor that came to him in parts.After starting the tractor the steering wheel turns hard to the right. Have tapped the steering vale assembly back and forth with no change.tractor is full of john deere power steering oil.no air bubbles in...- Rich M
- Thread
- Replies: 1
- Forum: John Deere
-
R
620 power steering trouble
Will jack tractor up tomorrow and c if wheels will turn.Will let you know then. Thanks- Rich M
- Post #1
- Forum: John Deere
-
R
620 power steering trouble
Helping a friend on steering problems. Steering wheeels are all the way to the right will not turn back to center or for that matter will not move at all. Have tried adjusting flow control valve.That didnt help any. Steering wheel turns easy with very little resistance at all. Power steering...- Rich M
- Thread
- Replies: 4
- Forum: John Deere
-
R
G radiator hose
Searching for radiator hose for G without going thru Mother Deere. Thanks in Advance Rich- Rich M
- Thread
- Replies: 5
- Forum: John Deere
-
R
valve clearance changing
great dain ,pulled top cover but found no play in camshaft. thanks- Rich M
- Post #1
- Forum: John Deere
-
R
Valve clearence
Pulled top cover but found no side to side play and very little foward or reverse on camshaft.cam followers and or cam? Or both ? Thanks in advance. Rich- Rich M
- Post #1
- Forum: John Deere
-
R
Valve clearence
rocker arm bolts are tight as this is what we originaly thought also. all valves have been reset several times with same results. any other ideas?- Rich M
- Post #1
- Forum: John Deere
-
R
valve clearance changing
In reference to a earlier post, if the cam needs replaced where do you suggest. Any certian grind?Tractor also has new valve srpings and valve clearance will change by turning tractor over two three times- Rich M
- Thread
- Replies: 6
- Forum: John Deere
-
R
deere g
Which air filter will fit in the can.looking for part number. Thanks in advance.Rich- Rich M
- Thread
- Replies: 3
- Forum: Tractor Pulling
-
R
deere head gasket
install roll crimp towards head or block/Thanks in advance- Rich M
- Thread
- Replies: 1
- Forum: John Deere
-
R
9 bolt hubs/deere g
trying to find a set of hubs for sale or someone to build me a pair- Rich M
- Thread
- Replies: 0
- Forum: Tractor Pulling
-
R
deere G
Mike M would like to visit with you on some possible engine improvements . Rich M @307-262-4908. Thanks- Rich M
- Thread
- Replies: 0
- Forum: John Deere
-
R
wd45
Looking for new friction blocks for throttle and hydraulic lever on wd45. Thanks in advance. Rich- Rich M
- Thread
- Replies: 2
- Forum: Allis-Chalmers
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy