(800) 853-2651
SHOP NOW

Recent content by rob bell

Yesterday's Tractor Forums
  1. W

    OT - Raynaud phenomenon - white finger problem

    http://en.wikipedia.org/wiki/Raynaud%27s_phenomenon Anyone else suffer from this problem? It started about 3 weeks ago - finger turns white, and starts to tingle when outside in the cold even when wearing thermal gloves. It does return to normal pink colour when warm. Doctor says its...
  2. R

    Ford 6610 brake shaft seals

    Does aht one have a schecmetic diagram of a brake shaft seal and components for a Ford 6610 tractor ?? I am having trouble getting it all apart to replace the seals !! My books only show the schemetics for a cab model but I need one for a no cab version to get parts off the shaft...
  3. R

    Front Idlers wear

    How much side movement is permissable in the idlers on a D4 ? What would be considered to be excessive and should I shim them up very firmly? The track chains are extended /stretched out to the max. Can I take out one link to give better tension on adjustment side? The sprocket still looks as if...
  4. R

    master pin removal

    Im trying to get the master pins out of track to undo chains. Itseems pretty tight. Is there an easy way to do this ie Heat & a bigger sledge hammer if so how much heat is ok and do I have to remove one or both pin Thank you any imformation would be appreciated . Rob
  5. R

    Aussie

    Thanks Bruce. Thought you might have dissapeared. I hope you get somthing this week end.We've had the D4 7U for about 45 years or more .It is my fathers oldy but its been good.Im now doing a bit of work to her fixing final drive leaks new fuel line and filters. Pulling out one whole side...
  6. R

    Aussie

    A hello to Bruce from AUS I sent you a note a couple of weeks back and was wondering if you happened to see it. regards Rob Bell
  7. R

    Aussie

    Gidday Bruce. I live on the other side of Vic down past Leongatha I d be interested to know if you have cat dozers especially a D4 and where you obtain spare parts I normally go through William Adams in Clayton Melbourne. Im sure there would be other places to chase up parts etc. thanks Rob
  8. R

    D47U year built

    Thanks Bruce oz I am interested to know if youre in australia or the US thanks, rob
  9. R

    D47U year built

    Sorry guys the serial no. for our D4 should read 7U 40767 SO its probably later than 1948 Any one now know the age ? thanks v much.
  10. R

    D47U

    Thanks OLD MAGNET. you are a wealth of knowledge! Can any one give the part no.s for the finaldrive as my book is hard to see exactly the part no. The no. I have is 5H389 in parts book and we are trying to cross refernce it at store. There is a big difference btwn prices ...
  11. R

    D47U

    Ive got agreat old D4 SERIAL No 7U4067 anyone know the year built? doing it up slowly Final Drive seals next then track over haul thanks
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top