Recent content by Roscoe22

  1. R

    IH 504 injector line leaking

    My IH 504 has a fuel leak where the #2 injector line from the pump attaches to injector,nut is tight,runs fine,but a steady drip that falls on pump,>Parts and repair manual show no seal at that point... Any ideas?? Thanks
  2. R

    1954 NAA lift

    Weird problem with the lift on my NAA. Relpaced lift piston and 0 ring to solve problem of lift leaking down slowly with mower on it.. Much better now ,not perfect but useable,. Used tractor about 3 weeks with no problems.Then after using tractor for a few hours one day lift stopped...
  3. R

    flipping the ring gear

    Well,apparently the 40H that Riverbend is working on had a 6 volt system and a worn out ring gear,so yeah it does happen,If it has been changed to 12 volts the problem will happen even sooner. No easier time than now to do it right.
  4. R

    flipping the ring gear

    Ring gears don't cost that much,do yourself a favor and replace gear,teeth that are left have half the metal to absorb starting load. I just went through a clutch and ring gear nightmare with my 504D that started with previous owner being cheap and flipping ring gear over to save a dollar. Same...
  5. R

    IH 504 utility auxiliary valve

    No squalling noise or straining,lever will only move back about half of normal travel.This happens all the time ,engine off or on.Remote cylinder hooked up or not.It worked for a few weeks trouble free then problem started again yesterday,same cylinder,same implement.
  6. R

    IH 504 utility auxiliary valve

    What would cause auxiliary valve for remote to hang up and refuse to move to lift position.? Lever will move to lower or float easily,when I pull lever back to raise position it will only go about half way and barely raises the cylinder.It did the same stunt a few weeks ago.I took valve...
  7. R

    Milwaukee 18 volts tools

    I have many of them,only complaint (other than the price of batteries) is two of my 3/8 impacts have the friction ring to retain socket,doesn't work well,sockets fall off at the worst times. Get the ones with detent pin to hold sockets on,you will be much happier.Have a1/2 drive will easily...
  8. R

    Fltwheel for IH 504

    Still being tortured by my IH 504 Utility with clutch issues. Clutch disc and pressure plate replaced ,splines on input shaft cleaned up,disc slides freely on imput shaft.Only way it will go in gear without grinding is to remove floorboard to allow extra clutch pedal travel. If I adjust linkage...
  9. R

    INT 504 clutch

    Split 504 again today.Took better look at clutch shaft splines.Two strange things,at rear of shaft were the disc splines are is a wear step,but it's all but covered by thePTO shaft . I know its been rubbing there because there is matching wear in trans side olf old. disc.Please tell me it's...
  10. R

    INT 504 clutch

    Jim,sorry I misread your post about wear on splines,thought you meant on flywheel,my mistake!.Probaly will split again tomorrow and look closer at shaft. It appears that idpt shaft can be replaced without too much hassle.I may have seen them on this site,will find one if worn too much,thanks for...
  11. R

    INT 504 clutch

    Pilot bearing is new,shaft slides in no problem.Splines look ok,not worn in any one spot.I did assemble clutch to flywheel before installing on tractor,that's when I discovered cover plate did not sit down in step for the 6 mounting bolts,had to grind a little off two of tabs to make cover plate...
  12. R

    INT 504 clutch

    Was wondering if a four puck disc like what was in it would release easier,don't like shooting in dark.Just doesn't appear that pressure plate moves much at all when the 3 fingers are pressed.Thanks Butch
  13. R

    INT 504 clutch

    lywheel was just ground,step per specs,so no step from old disc,that's why I split the second time,old disc was a 4 puck,not a woven,. Doesn't Look like lfingers are lifting pressure plate very much at all,even when adjusted too close to throw out bearing.Tractor not worked hard,clutch kit came...
  14. R

    INT 504 clutch

    Have installed new clutch disc and pressure plate in INT 504. Flywheel was resurfaced, step was set at 1.188 per IH book. Replaced four puck disc with woven disc. Clutch will not release no matter how I adjust linkage. Even with the 3 fingers touching throw out bearing (Not good) clutch still...
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top