-
rrlund replied to the thread oliver 70 engine.Those 70s used a Continental engine. The only ones to use it. Most of the other Olivers used an Oliver Waukesha. Whole different animal. -
rrlund replied to the thread Oliver fuel issues.One of us kids (not me) dropped a pop sickle stick in the gas tank of Dad's 66 one time. I got heavy and sank and would drift over the...
-
rrlund replied to the thread Oliver S88.Is there a question in there? Yes, those o rings on the sleeves can go bad. I bought a Super 55 cheap because they were leaking on that...
-
rrlund replied to the thread Rotary rake width for small square baler.Ya, I haven't been rake shopping since 87, so I'm not up on the models and specs. I assumed, when he said it was 13 foot, the rake was...
-
rrlund replied to the thread How often do you buy a whole tractor just to get a part?.I bought an Oliver 70 with a Chevy motor to get a 40 inch tire and the fenders. I only gave a couple of hundred dollars for that one though.
-
A good noise reduction headphone radio like 3M WorkTunes or Dewalt DPG 15 might accomplish more noise reduction for only around $60...
-
rrlund reacted to CraigWis's post in the thread Literature---1929 J.I.CASE Tractor Brochure pt1 with
Like.
Here is a 1929 J.I.CASE Tractor Brochure on the C and L series Tractors I Like looking at these older brochures. They Show a Lot of... -
rrlund replied to the thread Rotary rake width for small square baler.If that's the working width, sure, go for it. I've got a GT300 that I bought new back in 1987. If the Deere is the width that works for...
-
rrlund replied to the thread Rotary rake width for small square baler.Just because its for sale doesn't mean you have to buy it. There are narrower ones. If you aren't comfortable with it, keep on looking...
-
rrlund replied to the thread Levanna Road news.I've been through all of this before in the 70s and 80s. I don't have it in me anymore. I'll just bite the bullet, ride it out and try...
-
After the fourth attempt I have finally achieved a working clutch in my freshly repowered 1850. It turned out that the spare clutch...
-
rrlund replied to the thread Cotter pin on bottom of 2010.I had one of those get plugged on my White 2-135. Had a serious problem with the clutch slipping. I started wondering if there was one...
-
We bought this A from Kipp a couple years ago. He found the original receipt and dropped it off yesterday. Cool piece of the tractor's...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy