(800) 853-2651
SHOP NOW

Recent content by rust-o

Yesterday's Tractor Forums
  1. R

    hesston 5540 roundbaler

    It was parked inside if that makes any difference.... thanks for all the thoughts
  2. R

    hesston 5540 roundbaler

    I have the opportunity to get a hesston 5540 round Baler from a local farmer for $ 1000. Thing is it has sat in the shed since they stopped making hay a number of years back. (Maybe 10?) And it has a 2foot bale in the chamber. Should I run from this as things are probably stretched out or is it...
  3. R

    using air to move diesel fuel

    alright, thanks every-one for the quick response. this confirmed my suspicions!
  4. R

    using air to move diesel fuel

    I am in the process of setting up a fuel tank for fueling tractors, and have been exploring my fuel transfer possibilities. I have used hand crank pumps, electric pumps, and air to move fuel in the past, and air is my preference. My question is, is it safe to use air with a tank that is not...
  5. R

    Final Adjustments on a 165 lift cover

    Alright this looks like some helpful info. Yes my tractor has both pressure control and position control quadrants. I did only a few of the adjustments you mentioned, for some reason my manual didn't mention a bunch of them. But that is no surprise! my manual isn't the best. I will print...
  6. R

    Final Adjustments on a 165 lift cover

    Hi all, I have been in the process of rebuilding some hydraulic/pto related things on my 165 and almost have the project done. I also did the adjustments mentioned in the manual before re-installing the lift cover. Finally i am down to just 2 adjustments which are to be performed with the...
  7. R

    MF Special Tools

    Hi all, I am in the process of adjusting the hydraulic lift cover on a 165 The book says I need MFN 124, MFN 163 and MFN 970 Tools. From searching in the archives I have found ways to substitute for the tools. MFN 124 = 11/64 feeler gauge ( .17") MFN 163 = 3/8" thick piece of flat steel...
  8. R

    MF part identification needed

    oh I thought you where talking about a input bearing into the pump, which seemed strange cause it seems to just be a bushing. No i have the thing split behind the tranny. I'll check into what it takes to get to that bearing. I have a book, but it often leaves out what i'm looking for!
  9. R

    MF part identification needed

    Ok thanks Brendon, I noticed that the input shaft seemed a little sloppy. I'l check into a new bearing...
  10. R

    MF part identification needed

    Here is the picture, didnt have the right format... sorry i should have put a ruler or quarter in that picture for size reference, but the two roller type items are about 7/16'' long
  11. R

    MF part identification needed

    Hi all, I have been working at some hydraulic/pto stuff on my 165 and ran into a problem. I was replacing the control valve on the pump, but prior to taking any thing apart i turned the pump over and out rolled a couple small parts. parts b,c and ,d in the picture rolled out of the pump part...
  12. R

    Advice needed on my 165 hydraulic project

    Hey thanks! The lift arms re not binding as far as i can tell but i will definitly look into the lift cylinder seals. Also I have done a visual on the components of the draft control spring assembly and it all seems fairly good. are there signs i should look for that this assembly might be...
  13. R

    Advice needed on my 165 hydraulic project

    Hi all, so I have my old 165 torn down currently and am panning to put a new brake disc and shoe on the ipto clutch. But while I have the tractor torn apart and the hydraulic pump out i would like to resolve some issues there as well. Some background: The lift arms have very little lifting...
  14. R

    part number or name

    excellent, thanks!
  15. R

    part number or name

    Yeah I am looking for the brake disc as well. I emailed yesterdays tractors to see if they might be able to get the part in but I haven't heard from them. I might try calling tomorrow.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top