(800) 853-2651
SHOP NOW

Recent content by sbs

Yesterday's Tractor Forums
  1. S

    John Deere 6620 combine won't stay running

    I would check to see if your fuel tank cap is venting properly. Had a Massey Ferguson combine do that in the field. Opened the tank cap and air rushed in. Put a new cap on finished combining.
  2. S

    4020 Lift Link Disassembly

    Service manual say"s to press out the dowel pins
  3. S

    50 radiator again

    use a torch to heat up the ends the fastest and easiest. I would do both ends while it is apart. Use dish soap on the new o-rings and ends of pipe when you put it back together to make them slide together easier.
  4. S

    Relocate Batteries

    I wrap electrical tape around the handle of my wrench to avoid accidental sparking.
  5. S

    John Deere 50 entire gasket set (sets)

    http://www.external_link.com has gasket set
  6. S

    48 A front wheel wobble

    Sounds like the bronze bushings need replaced in the R.O.M knuckles.
  7. S

    PTO noise

    Using a 1968 4020 on a brand new 10" Farm King auger. When engaging the PTO lever there is a knocking sound coming from the back end of the tractor. Any help would be appreciated.
  8. S

    John Deere 620 oil clearance

    L.H. main bearing journal 2.749 to 2.750 inches R.H. main bearing journal 2.999 to 3.000 inches Main bearing oil clearance .004 to .006 inches
  9. S

    1951 B Clutch Drive Disk

    Make sure your the splines with the timing marks are lined up. The drive disk should be 1/8" to 1/4" from the end of crankshaft. You do not want the drive disk flush with end of crankshaft. If it is the crankshaft splines are wore out.
  10. S

    briggs and stratton

    I have a 12hp Briggs and Stratton model 300424 engine. I was wondering if a 10hp cylinder head would fit on and add more compression?
  11. S

    Kohler LP Head

    I found a Kohler cylinder head that appears to be a LP head but the casting number is not correct for the LP head. The casting number on the head is 235475 is this an LP head or am I wrong. Thank you
  12. S

    3020 Pedals

    foot throttle
  13. S

    JD 50 Quill Bearing Cup

    Weld a bead all the way around the bearing cup and as it cools the cup will shrink. Turn the cover upside down and the bearing cup should fall out.
  14. S

    farm sale

    Went to a farm sale today close to Johnson, NE one owner equipment. 4450 - $46,250 1970 3020 - $17,000 1964 3020 - $6,950 6620 SideHill - $28,000 7000 6 row planter - $4,750 Are these pretty comparable prices else where?
  15. S

    Belt pulley seal for late B question

    follow the groove to the underside of the crankshaft there is a hole there that is likely plug. The hole drains all the oil back into the crankcase.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top