-
B
Farmall M Engine Mystery
Trying to figure out what these letters mean on the stamping of this m block and why if it is a U code block which would be 51 that it has a 4 digit serial number. Any help will be greatly appreciated.- Boomer2431
- Post #1
- Forum: Farmall, International & McCormick
-
M
930 6 Speed block
I'm in search of a block from a 6 speed 930 diesel with a 401 "wide block". I haven't been able to figure out from the parts diagrams if 6 speed 930's have the wide block 401 in them, or just certain models (Western special, etc.)? The Case IH site has 3 or 4 different variations of the 930 6...- mshultz
- Post #1
- Forum: Case & David Brown
-
H
Did Oliver use rear rims that would swap out for Farmall?
I found a pair of tires and rims on craigslist from an Oliver. The pictures look like they would swap but I'm not certain. Did Oliver use the deep drop center rims such as on my Farmall M?- Happyfeet
- Post #1
- Forum: Farmall, International & McCormick
-
S
hold the phone........
I went back to the 35 to check for spark. I pulled the spark wire on the plug closest to the steering wheel, hit the starter and the engine coughed. what the heck I says. so I turned on the fuel, pulled the choke and with the spark wire still off the plug the engine fired up. put the plug back...- steve19438
- Post #1
- Forum: Harry Ferguson
-
J
John Deere LI with Herc Motor Pics
Just sharing some pics of this hard to find John Deere LI with the herc motor and factory Hydros Only 434 of these tractors where made not many had the factory hydros! It is getting torn down to finish one that im working on so some parts will be for sale if you need L parts!- JDChris
- Post #1
- Forum: John Deere
-
R
O/T Construction question.
I am an experienced carpenter, however.... I have been asked to make a waterfall in a house. Cement is out of the question, cement board or marine grade plywood will be the base and covered with flat rocks picked up from a nearby creek. I am sure the glue will hold but I am not sure what to...- Roger - Kansas
- Post #1
- Forum: Tool Talk
-
S
beater 2000 or 960
I have a 960 im considering selling, i live between cedar rapids and waterloo. -
S
Head issues
No, I didn't get these sleeves. I didn't know about them. I will get them coming. Thank you all for your help. -
S
Head issues
to John Smith 8n, Yes I picked up these washers today, The bags had the same part number on them so I didn't know which on was which. We tryed both washers on both valves. Later we found a cut away pic. of the exhaust valve setup on a website and they showed the washer you posted on the right as... -
S
Head issues
Typo; I'm guessing all I need are a different set of keepers. -
S
Head issues
The reason I am posting on here Rick B is I am looking for someones experience. I posted every part I bought and every step I did today hoping someone might see if I missed something. So I don't know what I could of left out Rick. If the fact that I didn't say the valve kit was a ' Tisco' kit... -
S
Head issues
That was 2 years ago, Cedar Rapids IA. I lost the radiator out of the deal at another shop too. The original head turned out to be junk, lot of cracks and 2 burnt valves. I'm just saying I don't have it for any kind of reference on parts I might need. Every head I found for sale comes with... -
S
Head issues
I bought a 960 2 years ago. I STRESS the fact that I am a IH man and I don"t know a thing about fords. When I bought this tractor It was supposed to have a bad head gasket. I sent the head off to get checked out, In the process the shop got flooded so that head is at the bottom of the Cedar...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy