(800) 853-2651
SHOP NOW

Recent content by slk

Yesterday's Tractor Forums
  1. S

    Presure Plate Fingers on Cub

    What is the measurement I should be looking for on the fingers of a pressure plate for a Farmall Cub??? Mine right now are measuring 7/8". This is a 1948 Cub.
  2. S

    Throw Out Bearing for Cub

    Does anyone have a cross reference number for the throw-out bearing for the Farmall Cubs. Everyone is saying NAPA has them, but NAPA doesn't have the info in their system to look it up.... Thanks Much Steve
  3. S

    Farmall Cub Clutch

    I did check it when I put the new pressure plate and clutch plate in 3 years ago. Now I did not think about taking that bolt out on the split ring that holds the T/O bearing. That might give me enough room to turn the yoke. There is no adjustment on my pedal Thanks Steve
  4. S

    Farmall Cub Clutch

    Ok this is what is happening. Through the inspection hole I removed the pin that was through the yoke going to the T/O bearing holder. I can't turn the yoke, because there is not enough room to make any more revolutions. Can you turn the rod going to the yoke from that small hole? Worse case...
  5. S

    Farmall Cub Clutch

    I looked in the inspection hole today and the bearing is still there in place and with no chunks out of it. With any luck maybe I can adjust the rod out some and make it work for a while longer. Will report back with any news. Thanks Steve
  6. S

    Farmall Cub Clutch

    Ok guys my Cub decided toady that it was not going to let me put it into gear. When I step on the clutch pedal it will not go in far enough to let me put the tractor into any gear. I can tell it is close to letting me but it will not. I put a new throw-out bearing in about 3 years ago and when I...
  7. S

    Timing a Farmall H

    How do you time an H with a timing light or do you???? I looked in my operators manual and it has some way that I have never heard of doing, and seams like a lot of steps. Has anyone here timed one with a timing light, and how??? Thanks Steve
  8. S

    Farmall H hard to start

    I did solder my cables.. Steve
  9. S

    Farmall H hard to start

    Now that I have not thought of.....Can you get hurt like you use to with the old cars??
  10. S

    Farmall H hard to start

    When I first start the tractor it turns over really good, just like it should. It only gives me grief after it has been running, and you shut it down, and try to start it right away. This is the scenario that happens quite often: I am out cutting with the brush mower and go through some heavy...
  11. S

    Farmall H hard to start

    My H is the pits to start after the engine is warm. Like if you are working with it and have to stop and turn it off it just does not want to turn over. It just turns very slowly like a dead battery. If I let it cool down about 10 min it will turn over and start up. If I jump it with 12 volts it...
  12. S

    Ford Dearborn 14-16 Scikle bar mower

    When using a ford dearborn 14-16 sicklebar mowers do they have to rest on the ground, or can you raise the 3 point hitch and cut about a foot of the ground with the sickle bar suspended???? Steve
  13. S

    Ford Dearborn 14-16 mower

    When using these types of mowers do they have to rest on the ground, or can you raise the 3 point hitch and cut about a foot of the ground with the sickle bar suspended???? Steve
  14. S

    Ford Dearborn 14-16 mower

    When using these types of mowers do they have to rest on the ground, or can you raise the 3 point hitch and cut about a foot of the ground with the sickle bar suspended???? Steve
  15. S

    Ford Dearborn 14-16 mower

    I have a brush mower I pull behind a farmall H. Problem is I can't get off my road even 2 feet or I will sink the wheels in a bog on both sides. The road is firm but much off to either side is muck. I have a chance to pick up a sickle bar mower but have never used one. It was on a Ford NAA...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top