(800) 853-2651
SHOP NOW

Recent content by steve 43

Yesterday's Tractor Forums
  1. 4

    Advise on Smaller Tractor Model

    Looking to get a smaller tractor, 311B, up to a 400 series and I like the headlights in the nose. I've got a 530 diesel sitting for me when I get a large enough place so looking for something smaller. I really like 311B's but they were only around for a couple years. I was thinking I could...
  2. B

    Batteries on 4020

    I would like to put 2 12 volt batteries on my 4020 to replace the 6 volt but I can't remember how to run the cables, does anybody have a pic on how to do this please?
  3. B

    MF 20 loader on MF 135

    I bought a MF 20 loader from a farm auction and started mounting it on my MF 135. I am running into a few fitting issues and looking for people that also have this loader on the same model tractor. The side mounts have multi hole placement for the rear axle ubolts. I have them in the farthest...
  4. S

    mf 20 with three point

    I am looking at amf 20 industrial with loader and three point and shuttle shift. I would like to put my three point snowblower on the back but owner says the pto reverses while the tractor in backing up so will I be SOL as far as being able to use my snowblower?
  5. S

    stress on engine block

    If the goal is to drop oil pan then isnt there just as much stress on the block whether it is done bolted to the tranny or on an engine stand?
  6. S

    drop oil pan

    What did you grab at front of motor?
  7. S

    drop oil pan

    I do have a cherry picker...I wonder if there is any way I could use that?
  8. S

    drop oil pan

    If I drop my oil pan on my 43 by jacking up the tranny and swinging front axle out of way will the engine drop on me? Can the engine block be cantilevered out like that without snapping off?
  9. S

    generator maintenance

    I can hear my generator sqeaking when it runs...I see one oiler on one end but how do yo do the other end?
  10. S

    govenor adjustment

    How should the adjustable screw on gov be set?
  11. S

    govenor spring adj

    I have read that the govenor spring on my 43 should have no play or preload at idle. The prob is at idle the adj screw is a long ways a way from the stop even turned in all the way...I dont see any other places to make adjustments.
  12. S

    carb adj

    On my 43, if I start with the mixture screw out 1 turn and turn out 1/8 at a time till fastest idle then slow it down with idle screw and do this 3 times. Do you start over at 1 turn each time and where should the idle screw be set at initially?
  13. S

    inner lever on governor wobbles

    My inner lever on my governor on my 43 is quite sloppy on the governor housing...the governor housing seems ok but the lever is worn on a taper.
  14. S

    small screw in end of centrifugal advance by offset tang

    I thought youse guys always said to not add oil in around distributor cuz it'll eventually get on the points. I thought that the bushings were oil impregnanted and didnt require lubbing????
  15. S

    small screw in end of centrifugal advance by offset tang

    Curiosity got the better of me and I tried to remove this screw on my front mount 2n. It only went out till it got flush then stopped. So I turned it back in till it stopped but that seemed to be deeper then when I first started fiddlin with it. So I guess my question is what does this screw...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top