Recent content by Steve Gillespie

  1. S

    8N Starter Won't Engage

    OK, well with the help of my #1 Son, we got the rest of the starter out, got it put back together and put back in, and best part - worked like a charm! So I'm back in biz again (for now). Thanks for all the help, guys!
  2. S

    8N Starter Won't Engage

    Thanks again, Dell - at this point, I will replace the whole starter, IF I can get it out! The armature end of the starter and bendix/drive are still stuck in the bell housing. I pried & tapped a little on the end plate, can get maybe a 1/8" gap but that's it. Any ideas? Steve
  3. S

    8N Starter Won't Engage

    Part Two: OK, guys, I priced a new starter today at my local Tractor Supply. My next question is, the new starter already has the new drive. So how do I get the *old* drive out? (looks like I must pry off the round plate at the engine housing - is it that simple? - will it have to be pressed...
  4. S

    8N Starter Won't Engage

    Thanks again, Dell - well, I really screwed up now - I loosened the starter bolts and tried to wiggle it, to see if it would unfreeze. But I apparently pulled it out too far, and the end plate popped off, allowing the brushes to free, and now I am not able to get anything back on. Is there a...
  5. S

    8N Starter Won't Engage

    OK, I'll try that, Dell - many thanks! So where do I find one of those new 'clutch-type' starter drives?
  6. S

    8N Starter Won't Engage

    My '49 8N starter won't engage. The solenoid clicks, and after repeated attempts, the wires begin to overheat. I tried the old 'jump at the solenoid' but did not work. I then replaced the solenoid, but same result. Is the starter bad, or something simpler, like the ignition switch?
  7. S

    Lack of inner axle seal on 8N 09-26-2008 followup

    Thanks, Joe - I might try it myself, but prob not til next Spring, as the days are getting shorter, I"ve pretty much laid by by yard, and it"s deer season, so I"m gone every weekend til January! :-)
  8. S

    Lack of inner axle seal on 8N 09-26-2008 followup

    p.s. Guys, I just went back to the 9/26 thread, and also saw the ref to JimSmith 'fixit' site for this problem - waaay over my head - so looks like I'll be spending a lot of $$ on fluid. :-(
  9. S

    Lack of inner axle seal on 8N 09-26-2008 followup

    Dale & Mike, my '49 8N has leaked hydr oil from *somewhere* on the left rear hub (I can see 'stains' where it runs down the wheel). I just noticed this week, the hydr box was BONE DRY - took 5 gal to refill. How much of a job is that to fix (for a tractor rookie like me)?
  10. S

    8N Carburator Problem

    Well, maybe I'm an Idiot? - went back last evening and it started and ran fine - maybe I had the key off? Thanks again for all the help!
  11. S

    8N Carburator Problem

    Well, I was mistaken about the hole being threaded - you just tap the porous strainer 'plug' in to the hole and that seemed to do it ... So I pulled the little carb and did that, went to put it back on, and as my luck goes, one of the carb studs broke when I was tightening it. So pulled it off...
  12. S

    8N Carburator Problem

    OK, I got my $6 part at the JD dealer yesterday. But one more question: it's a simple little 'strainer' plug, i.e. not any kind of 'screw' or bolt (no threads). However, the hole in the bowl it came out of is threaded. Does it just pop in? - if so, will it stay? Going out in a minute and...
  13. S

    8N Carburator Problem

    OK, thanks again, All! - the 'local' John Deere store is ordering me a replacement strainer (as Bob suggested) - cost ~$6 - picking it up tomorrow morning. I may just plug it in and see how she runs first ... if no luck, it's a tear-down, clean, and readjust. If that doesn't work, I guess a new...
  14. S

    8N Carburator Problem

    OK, many thanks, guys! - I guess it's off to the local John Deere dealer, to try to order another one ... failing that, a new carb is about $120. Steve
  15. S

    8N Carburator Problem

    OK, thanks, Dunk! - I could not imagine what I did to cause it to miss so badly, just by removing the lower body, plugging the hole, and re-installing ... guess I broke some dirt loose somewhere? I'll remove the whole carb, disassemble, and clean it - see what that does. BTW, do you think JB...
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top