(800) 853-2651
SHOP NOW

Recent content by svenandersen

Yesterday's Tractor Forums
  1. B

    Band saw blades

    Looking for recommendations for metal cutting blade on band saw - How many threads per inch -will cut 1/8 to 1/2 steel
  2. G

    steering componant ID help needed

    i hate to ask questions that are considered simple to many people that are experienced with these machines. i am going to replace steering components on my 2n, the ball joints where the steering sector shaft bolts to what i am calling a drag link is worn, along with the joint at the front of...
  3. E

    Re-wiring a '52 8n

    Good evening everyone! I am ordering a bunch of parts including a new wiring harness and am looking at several wiring schematics and have a few questions. I am re-wiring it because the harness has far to many splices in it and most of the wires are now red. It has been converted to 12v...
  4. N

    Help to identify Farmall 460 broken part

    I am trying to help my neighbor with his IHC 460. Can someone educate me what this unit is and what gear he has broken? And where he can get a replacement? I'm more used to Fords and John Deere and a bit ignorant over here in the Red. The photos tell it better than me, thanks for any help, Paul
  5. P

    Piston Ring Gap

    I have pulled the sleeves on my Ford 640 and replaced them with new. I have fitted the new pistons to their respective cylinders. I now need to gap the rings. The manual calls for a 0.01 to 0.02 gap. Persons on here suggest a 0.003 to 0.004 gap per inch. The bore is 3 7/16 or 3.4375...
  6. J

    Tree cutting issues

    Did not want to jump the other two tree cutting (stuck and troubled) ones but some years back we had a good one. I was cutting and a guy was running a 440 John Deere. Mixed wood but that day we were doing hardwood. He came in and started backing the skidder up so we could hook up. A small maybe...
  7. P

    fused switch

    Hi 1950 A the volt meter , hand held jumps all over when running, does the fused switch have any thing to do with this? Thanks Dave.
  8. T

    D239 wet sleeves?

    Im doing a rebuild on a D239 engine that i want to put into my 574. My first question is which o-ring do i use on the sleeves. The red dot(bigger) or yellow dot. Supposedly its dependent on the serial # but I cant find anywhere in the manual that tells you which one to use. The serial # on the...
  9. M

    6' Offset Disk

    Was searching through the local craigslist things for sale, and came across an add for a CASE 6' Offset Disk. Model Number on nameplate is - XRT 531011. Have never seen one like it, saw a 6' bog disk once while visiting Loren, but this appears to have both sides anchored with angle iron so it...
  10. C

    1650 diesel or 1850 diesel

    If you had a choice of 1650 diesel in really good condition low hours like 4500, vs an 1850 diesel in rough condition with high hours 7600 hours, but runs good. Which would you buy? I would be using for plowing with a 3 bottom trailer plow, and pulling a 12 ft culti-mulcher and 12 ft disk. the...
  11. R

    160 Power Steering Valve

    I have a 160 that has a power steering problem. Steering works fine around the yard at low speeds but malfunctions at road speed. I also cannot steer the tractor when it is not running. Shop manual seems to suggest there is something wrong with the steering control valve. Anyone know where I...
  12. J

    diagram needed for hydraulic lines to pump and levers

    I am changing over my hydraulics system to a pump that runs off the crank shaft. I need a diagram of the hoses leading from the hydraulic 5 gal resevoir to the pump both the in and the out hose. I also need the hoses from the pump to the levers.
  13. G

    Another Rustyration!

    Hello, From the looks of the wheels and hubs, it may be ready for the body shop, Guido.
    • guido
    • Post #1
    • Forum: Tool Talk
  14. C

    3010 PTO idler gear

    Finally got the 3010 split, it isn't the pin for the PTO it has been deleted with a chunk of steel. Instead it is the PTO idler gear that is coned for the PTO brake. Think we have all the needle roller but want to make sure. Do you know how many should be there?
  15. F

    adjusting H Farmall carb

    Had to get a new er top for the carb. Got it back from the mechanic today. Ive had it on and off 3 times now. It dosnt run right. It dosnt idle, and it DOES race. Im 70, and ive forgotten which screws do what, other then the idle adjustment screw, which comes out from the top straight...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top