(800) 853-2651
SHOP NOW

Recent content by tdow

Yesterday's Tractor Forums
  1. T

    Ford 841

    I have thought about the temperature, I don't know if it does have a thermostat or maybe it is stuck open. It will just barely get into the green on the gauge. I have seen it get a little higher not to the middle of the gauge just into the green. I noticed that if I sped the engine up a little...
  2. T

    Ford 841

    Ok, thanks for the response. I would think it would be nearly impossible to leak enough gas to get it into the cylinders but there is gas in it. If I had a bad spark plug or plug wire and it was just filling the cylinder with gas do you think that could cause it to leak into the crank case? Or...
  3. T

    Ford 841

    Thank you for the response. I have had the tractor since last August and I haven't used it much. The hydraulics didnt work when I got it and I spent some time fixing that. Since ive been using it I blade the road. I use the scoop bucket to bring road material to patch washouts in our road etc...
  4. T

    Ford 841

    Thanks. I changed all the oils after I bought the thing and the oil didnt have a gasoline smell. So hopefully it is just a fluke. I will change the oil again and see what happens. Ive been pretty careful about closing the sediment bowl after using it. Possibly there is enough fuel in the line...
  5. T

    Ford 841

    I bought a 841 ford last August. I recently had to replace the clutch. That all went well. I put the last bolts attaching the hood and i walked by and checked the oil. The oil level was at the proper level. I smelled the oil and tried to convince myself that I didnt smell gasoline in the oil...
  6. T

    Ford 841 clutch hanging in gear.

    Thaks for the input. I will adjust the clutch linkage a bit more and see if that helps. If not then I guess I have to split the tractor and replace the clutch.
  7. T

    Ford 841 clutch hanging in gear.

    If im moving down our road at say 10 mph 1000rmp in 4th gear and I push the clutch it seems to disengage and operate properly. If I stop and get off the tractor while running in neutral when I get back on it and press the clutch it is hard to get back into gear, I grinds and so on. I have to let...
  8. T

    Ford 841 clutch hanging in gear.

    I have noticed over the last few weeks when running the tractor, ford 841. It will hang in gear when the clutch pedal is all the way to the board. Particularly in reverse and first gear. I can be just at idle be backing it out of the barn and I push the clutch in and I keeps pulling in reverse...
  9. T

    ford hydraulic o rings.

    Thanks for the o ring size. I got some ordered. Very disappointing Haha. I thought I was going to get that thing done today. I would have thought they would come with the top lid kit.
  10. T

    ford hydraulic o rings.

    thanks. yeah I found them on messicks in the rear axle category
  11. T

    ford hydraulic o rings.

    I am finishing up repairing hydraulic top lid on my ford 841 got all set up to put the top back on this afternoon and went to get the O rings for the pressure and suction tubes where they come up and and meet the lid and out of 2 sets 2 top lid gaskets 2 top lid O ring sets I cannot find O...
  12. T

    ford 841 hydaulics troubleshooting.

    On a recent purchase of a 841 ford tractor i am having hydraulic problems. I have posted about it before. I havent had to time to get into it very deeply, my weekends have been very busy for the last few weeks. This morning I had a few minutes before we leave for oklahoma city and I drained...
  13. T

    Unload valve for 801 ford

    Thank you. I think i just needed to flip a page in my manual.
  14. T

    Unload valve for 801 ford

    Thanks for the insight and advice. I also have, what I think is called the pump relief valve. It is the one that is in the bottom of the sump that is accessed under a plate on the right hand side or the tractor. The guy i bought the tractor from thought that might be causing a problem. The...
  15. T

    Unload valve for 801 ford

    With the draft control lever in the down position, draft control, it does nothing ever. With the draft control level in the horizontal position, position control, it will sometimes lift about half way. I can kind of coax it up a bit higher by lowering the touch control lever then pulling it...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top