-
T
Ford 3400 with 730 loader
thought I had assembled it properly however now I am not sure. I will take it apart and check it out. Thank you.- Tiber56
- Post #1
- Forum: Tractor & Farm Talk
-
T
Ford 3400 with 730 loader
I have a vane type hyd pump for my 730 loader that I replaced the spline shaft,seal and bearing. I took pictures as I disassembled it to guide me in reassembling it. Back together and filled with fluid. I cracked the out put line and I have fluid to that point. I get no response. I did get a...- Tiber56
- Thread
- Replies: 2
- Forum: Tractor & Farm Talk
-
T
730 loader
n my search for a new filter It seems there are 2 filters and I have not taken mine out yet to verify which one I need. -
T
730 loader
s I am a novice at this I am baffled that the hydraulics for the loader do not work. I took pictures of the pump as I took it apart and I thought I put it together properly. Fluid level is good. As the loader was working good until the splines stripped I wonder if the filter may be plugged. I... -
T
730 loader
I am looking for a supplier to get a new hydraulic filter and a vent. -
T
730 loader
Looking for the hydraulic filter for the loader and the filler vent. -
T
Ford 3400 Hydralics
hank you. operator error in regards to the three point lift it works fine. The loader is still a work in progress.- Tiber56
- Post #1
- Forum: Tractor & Farm Talk
-
T
Ford 3400Need
hank you for the help. I was able to get the parts to rebuild my pump. I replaced th shaft, seal and bearing. I cracked the out put line tell fluid was flowing. Started the tractor and no response in the hydraulic system. -
T
Ford 3400Need
hank you. Is Thera place that is best to bleed the system. I replaced the shaft,seal and bearing in the vane type pump and loosened the out put line and I am not getting any movement. -
T
Ford 3400 Hydralics
I replaced the shaft and seal on my vane type front pump for the 730 loader. The pump was working tell the splines on the shaft and hub stripped. After putting everything back together I filled the tank with fluid. I cracked the out put side of the pump tell fluid ran out. I started the tractor...- Tiber56
- Thread
- Replies: 2
- Forum: Tractor & Farm Talk
-
T
Ford 3400Need
hank you. Does your loader pump have the inlet and outlet on a horizontal plane and a somewhat egg shaped flange on a vertical plane. My pump is square and is 3 layers. I have not been able to locate any numbers on it. When I tried to order a pump the number we came up with for a 730 loader is... -
T
Ford 3400Need
Need help in ID ing the front end loader on my Ford 3400. Pictures attached. I need a new hydrulic pump as the splines are stripped on mine.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy