-
T
Bd154 no fuel
ok update- i removed the lid, and found the pump was filthy inside. dirt/rust/who knows what. so at this point im fairly certain its going to have to come off. question- is there any specific timing setup i should set this thing on to pull it? I did look through the little window...- Tiger Joe
- Post #4
- Forum: Farmall, International & McCormick
-
T
Bd154 no fuel
Have an old IH3444 backhoe with I believe the BD154 diesel. Thing always ran great until 6-8 months ago. Just won’t start. Spins over great just doesn’t fire. Tried some quick searching here is what I did: 1- I cracked both bleeder screws on pump. I have fuel spraying out great with...- Tiger Joe
- Thread
- Replies: 4
- Forum: Farmall, International & McCormick
-
T
Question on snow plow
Stumbled on this front plow setup local to me and wondering if it might be for a 3000. I have a front blade setup for a 800/801 and I know this is different. Looking. I asked the seller and they don’t know. I found a pic on the forum from years ago and if definitely looks similar. So... -
T
Where to check hydraulic pressure on 3000
Unfortunately mine never goes over 2,000. Idle, higher rpm doesnt matter. Gauge smacks 1800 and never moves -
T
Where to check hydraulic pressure on 3000
ok so I had time to check the pump again. good news now is it appears I got the leak stopped. bad news is no change, the pump is makiing around 1800 with the lift chained. so what now? can I live with 1800 psi not the 2500 it should have? could the relief valve be bad? I... -
T
Where to check hydraulic pressure on 3000
Ok pulled the pump off again today and checked it out. Didnt see anything I thought might be an issue so put it all back together. Made sure everything is tight. No change. Lift chained the pump only hits 1700 psi and fluid starts leaking out at the gaskets/plate. -
T
Where to check hydraulic pressure on 3000
Yes rebuilt. Yes that is where its leaking. I had an unknown leak before when I lifted my brush hog. Im guessing it was always leaking here and I couldnt find it. Is there a chan e the pump housing is messed up at all? Or should I try new gaskets? Tractor is new to me last year so... -
T
Where to check hydraulic pressure on 3000
No I didnt put sealant on the gasket was afraid to with how close it was to all the pump internals. -
T
Where to check hydraulic pressure on 3000
so i just looked at messicks website, the o ring appears to be on the suction side, the leak where i have it- where the pressure housing with the 6 bolts connects, appears to only use gaskets. I did replace those gaskets when i rebuilt it -
T
Where to check hydraulic pressure on 3000
Cant edit but now Im thinking wanted to add: The whole issue that started my pump rebuild was a hydraulic leak when lifting my brush hog. Maybe it has always been leaking here. I think there is a big o ring inside the pump there. Unfortunately my rebuild kit was missing that for some... -
T
Where to check hydraulic pressure on 3000
Ok I checked it there this morning. Only got about 1700-1800 psi on my gauge with the lift chained down. Interestingly, while I was trying to check the pressure, I see a stream of fluid coming from my pump. Appears to be where the rear half bolts to the front. I just went through this... -
T
Where to check hydraulic pressure on 3000
So since my lift is still slow in my 3000, I want to check my pump pressure make sure I didnt mess up the rebuild. Im reading the I&T manual and am slightly confused. They seem to reference 3 different places to check pressure: 1- at pump using the plug for priming 2- at pressure... -
T
Ford 3000 hydraulic pump
Yes I still have the black flow knob. I think you are correct turn in for quicker. Honestly now I am questioning everything and I cant even remember how quick the lift was before. What I did notice now if i pull up on the handle to raise the lift, it takes about 3 seconds for the arms to... -
T
Ford 3000 hydraulic pump
ok update. I decided to just order the new o rings for the suction line just to eliminate that as a problem. pump primes without issue. my 3 pt lift is still very slow. I tried running a hose back to the rear end, did not really see any bubbles, let it run like that for 15 min... -
T
Ford 3000 hydraulic pump
yes mine is the old style manifold with 2 o rings. I'm debating taking it back off and changing the o rings out for new ones just to eliminate that as a possible issue.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy