(800) 853-2651
SHOP NOW

Recent content by Tilman

Yesterday's Tractor Forums
  1. S

    Ford 2000 hydraulic line

    I recently bought a 1973 Ford 2000 tractor and when the seller was showing me the tractor he pushed the hydraulic lever and blew the line out at the connection to the hydraulic pump. Seller bought me a new nut and and seat for the metal hydraulic line coming out of the pump and said that the...
  2. T

    Value of a 706

    I live in North Dakota where it makes national news for snow and cold weather. Up here the 706 Gas tractor has a great cold start reputation which is why I bought one. 6000 hours, decent paint, hydraullics and steering work well, tires 60% f&R, After puting a tuneup on the engine and changing...
  3. T

    RE: Farmall 706 brakes

    On July 9, 2009 I posted a help (71.158.222.210)request about my gas 706 Farmall brakes and hydraulic problems. "bc" answered with some helpful suggestions. bc asked me to post back what I found out. Here goes. The hydraulics were simple. Change the filter and clean the screen was part 1. The...
  4. T

    Farmall 706 brakes

    I recently bought a 706 Farmll and it is having the following problems: slow hydraulics, left brake grabs very hard and right brake does not work at all. Tractor has 6500 hours on it and appears to be in generally good condition.
  5. T

    47 8N hydraulics

    My working antique is a 1947 8N and the 3 point lift has some problems. They are:(1)Only have position control for the top 1/2 of the control lever movement.(2)Jerky lift when cold. (3)Screeching noise on heavy lift-over 600 pounds. (4)Wont consistantly lower when raised with a heavy load. (5)...
  6. T

    Running out of ideas

    Dell, Thanks for the very direct carb adjusting directions. When my 47 8N got cranky and didn't want to starty at -22 below and I burned out the (new) coil, i followed your directions on the carb -readjusted the points andf replaced the coil which caused it to start up like a summer day. Of...
  7. T

    8N with front blade

    Could you email a closer up picture of the snowplow frame and the blade mount and lift mechanisim? Thanks
  8. T

    8n started at 5 degrees

    My 8n started at 12 below the other day. I guess I help this happen by plugging in a 1500 watt tank heater. Yes I push the clutch in while starting. Also use a 300 watt magnetic heater on the transmission near the hydraulic pump. Another tip is to take your PTO out of gear before starting. It...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top