(800) 853-2651
SHOP NOW

Recent content by todd wheelbarger

Yesterday's Tractor Forums
  1. T

    955K TORQUE

    you were right, i made everything work, should be fine
  2. T

    955K TORQUE

    my input shaft to engine #is 1t946 has a shorter splined shaft than hectors. that # is 1t732, that splined part of the shaft is 1/2 inch longer. will i have room to put the rubber couplers on engine to trans and is that why my old convertor went bad? what keeps the convertor from going back and...
  3. T

    955K TORQUE

    i have assembled the torque as per manual and the torque will move 3mm on groung sleeve, is this normal?
  4. T

    955K TORQUE

    got my parts from hector today and they are perfect. i think i will take a vacation day and put it together. thanks everyone!!! if i can help anyone out on ford cars and trucks give me a call or ping me
  5. T

    955k torque shot

    that is what i wanted to know. now i need your info hector
  6. T

    955k torque shot

    so are you saying that i will have to use some of the parts in my torque
  7. T

    955k torque shot

    sorry to hear about the accident. the parts that are no good in my convertor are the ground sleeve or support,the allumium piece that is splined to the support(stator)?, the bearings on the support, bearings for the stator, sealing rings, the back cover that slides over the support has a cast...
  8. T

    955k torque shot

    hecter how can i tell if your convertor will fit, and did you take it completely apart
  9. T

    955k torque shot

    YES! this web site has the best group of guys, doesn't it
  10. T

    955k torque shot

    my # is 61h452
  11. T

    955k torque shot

    does that mean hecter's won't work?
  12. T

    955k torque shot

    so i see a nut and lock washer on topof trasn by the shaft, is that the tapered shaft
  13. T

    955k torque shot

    finally got convertor completely apart and the ground support,part of the alluminum turbine, snap ring and bearing and races are chewed up! now do i buy hector's, fix mine or buy a reman? also i am taking the shift shaft out of top of trans, really loose. the valve body is out, but what about...
  14. T

    955k trans fluid bypass valve

    bob had me take some pressure readings ,and i fixed the pipe that runs from the convertor housing to trans. i have had the cooler off, and it was spotless, but i can't remember how i checked the bypass
  15. T

    955k trans fluid bypass valve

    where is it located, i thought i checked it a couple years ago, but i can't remember
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top