(800) 853-2651
SHOP NOW

Recent content by TractorTucker

Yesterday's Tractor Forums
  1. T

    Old drill press?

    I have one very similar. You can put a hand crank on it to use it by hand.
  2. T

    I'm ready to give up

    I just had a massey that I was having trouble getting to run right. It would start, and sometimes it would work okay, others it would stall out, and most of the time it felt underpowered. I finally figured out that it was the condensor. I ended up swapping between 3 or 4 before I found one that...
  3. T

    Allis Speed Patrol grader

    This is for sale near me and I'm very tempted to try buying it, but it has me a little confused. I thought these speed patrols were just based on wc models? This looks like a wd45 to me because of the snap coupler. Was it maybe one that someone retrofitted the grader parts to a later...
  4. T

    Grandpa Love

    Just buy a bale baron. It makes little squares so much nicer to pick up off the field.
  5. T

    Starts but will not move

    Are you sure you have the range lever engaged? I've been running a newer kubota lately and the range lever really doesn't like being shifted from low to high.
  6. T

    Hydraulic loader problem

    Hopefully the problem is as simple as that. I need to find seal kits for it, but I do have plans of rebuilding the cylinders. I hate loaders that leak down.
  7. T

    Hydraulic loader problem

    I don't think they've been replaced, the paint on the cylinders matches the rest of the loader and if I slowly feather the valve they will extend or retract all the way.
  8. T

    Hydraulic loader problem

    I recently picked up a Massey 204 for a great price, and after a tune up and carb rebuild it runs a lot better than it did when I got it. I have an issue with the loader however. When I try to curl the bucket, up or down, when it reaches the last few inches of the cylinder it bogs down the...
  9. T

    My 96 Dodge Ram 3500

    Maybe it was the steering wheel lock? When you rolled forward it twisted the wheel which locked the ignition switch?
  10. T

    The DC is fixed

    On my DC, I was able to get the snap ring out throught the clutch inspection hole. After all the time I spent fooling with it, it might have been faster to split it. I ended up buying 2 or 3 different snap ring pliers before I found one with just the right angle to work.
  11. T

    Some progress on DC

    I wish I had thought of the sprayer for cleaning out my rear end. Did you have fun with the snap ring to get the pto shaft out?
  12. T

    Dc motor off ac power

    The picture is the tag on the wire feeder, it plugs in. The welder is an old lincoln lincwelder 225.
  13. T

    Dc motor off ac power

    I have an old engine driven welder I just got running decent and now I'm wondering about the feasibility of putting this wire feeder on it for occasional sheet metal work. My welder has a 110v outlet at 50 hz. This wire feeder I believe has a DC motor, is there a simple way to run it off the welder?
  14. T

    871 select o speed

    When you moved the lever to put it in park did the tractor remain in the same gear it was already in? Does the pto still work? My guess is you either stripped the splines off the input shaft, the rivets in the clutch broke, or your shift cable broke.
  15. T

    1 arm loader value

    How much would a dual spool valve bring? I offered 400 if he had the valve and he hung up.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top