(800) 853-2651
SHOP NOW

Recent content by ugabulldog

Yesterday's Tractor Forums
  1. U

    rear remote control lever question

    This is on a '04 MF but I figured someone could help please...To operate FEL the control lever beside seat for the rear remotes has to be tied back and loader is control by joystick on loader mounted valve. I always lower loader when parked but does it hurt anything to leave control lever tied...
  2. U

    removing fuel line

    is there an option other than purchasing exact replacement line, looks to be expensive.
  3. U

    removing fuel line

    oh yes, I remember now from a few years ago doing this....do the new lines come with new rubber gaskets I wonder?
  4. U

    removing fuel line

    Is there a trick to removing a fuel line? Nut is loosened all the way out, I know the end is flared but I am pulling pretty hard and line won't budge?? Thanks (MF 245 diesel)
  5. U

    help adding FEL to 245 tractor

    I would like to add a FEL to my tractor and am new to this, what would I need as far as hydraulics to hook it up? I have attached some pictures if this helps. I know I need a mounting bracket. If I buy new the dealer could tell which loaders fit, if I am looking at used loaders, how do I know...
  6. U

    tie rod came loose

    thanks, I think...... this one doesn't have a grease fitting on the bottom.
  7. U

    tie rod came loose

    245 owner here, as you can see in the picture my tie rod came loose. Admitedly I don't know much about this,... I have an operators manual that tells me how to do a front wheel alignment, how is tie rod held on to the ball??
  8. U

    fuel shut off silcock

    also, is this is the correct line for the fuel filter vent?? (I know there are two on the injector pump also) thanks
  9. U

    fuel shut off silcock

    I know I ask alot of basic questions....thanks for everyone's help!!I need to air bleed fuel system on 245 diesel and boy is it taking FOREVER to get fuel flowing with manual pump (i have bumped starter also). I just want to make sure that fuel shut off silcock from tank is turned all the...
  10. U

    do I need to air bleed fuel system?

    I replaced this gasket (where two bolts w/ wire are)on my fuel injection pump, do I need to air bleed fuel system? Thanks
  11. U

    removing hubs

    thank you, great write-up!!
  12. U

    removing hubs

    I want to inspect/repack wheel bearings on my 245. How do I remove hubs from spindles? Do I need to take off hubcaps (do they screw in)? I have manual but it doesn't say and I couldn't tell from looking at. Thanks
  13. U

    MF 245 fuel injector pump leak

    what is that wire for?? Are you not supposed to tighten bolts very much and it helps keep bolts from loosening?
  14. U

    MF 245 fuel injector pump leak

    great, thank you.
  15. U

    MF 245 fuel injector pump leak

    it is a big leak from plate with two bolts and wire are, please advise??
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top