(800) 853-2651
SHOP NOW

Recent content by VPC1

Yesterday's Tractor Forums
  1. V

    XT190 motor

    We have two 860 cotton strippers complete with good running engines. Located in Oklahoma.
  2. V

    Farmall

    Just wondering where I might get a listing of the prefix letters as you have stated in this post? I think mine are IAAM.
  3. V

    Farmall B

    Yes it does have a water pump.
  4. V

    Farmall B

    I called them this morning and have been waiting on a call back all day,,,as a matter of fact, I've been waiting on 3 call backs from 3 different companys! Guess this one's going to be a real pain. Craig.
  5. V

    Farmall B

    I was reading in the classifieds and saw where someone had a baler engine for sale and they were listing it as a C113 or a C119?? Ever heard of one of those? Craig
  6. V

    Farmall B

    Okay,,,,lots more problems it seems. Block serial number is 16731, sleeve length is 6-7/8, diameter at seal is 3-7/16, and bore is 3. Doesn't seem that anything on this site will match up. Pistons are 3-1/2 in length and are a 4 ring piston. Any ideas???
  7. V

    year-a-round cab

    Sounds like air lock to me. I would unhook the return line at the engine and run the tractor and let it push the air through the line. I've have had this problem before. Very common with the core being high above the water pump.
  8. V

    Farmall B

    I'll do that tomorrow,,,thanks for all the info. Craig.
  9. V

    Farmall B

    The block has been to the machine shop, vatted and checked and it"s sitting in my garage ready to go. Standard crank has been polished and also ready to go. I just need to make sure I get the correct engine kit. Thanks,,,,Craig
  10. V

    Farmall B

    I had checked the serial number back a couple years ago and was not able to find a kit for it but I do know it has the 3 inch bore piston and the lower sleeve OD is 3 7/16. I would like to go to the larger bore if possible. Craig.
  11. V

    Farmall B

    The pilot shaft bushing is the same and it does have provision for a hydraulic pump. Thanks for the info. Craig
  12. V

    Farmall B

    Does anyone have any information on the 4 cyl engine used on International hay balers? I have one that I'm planning to overhaul and put in a Farmall B but need to insure I get the right overhaul kit. Thanks.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top