(800) 853-2651
SHOP NOW

Recent content by Warren W

Yesterday's Tractor Forums
  1. W

    NAA oil

    Thank you for the info, I was unshure of using hyd. oil for everything. I thought the rears would be 80W-90 and trans. I always use utf on all hyd. systems. Thanks again for the info and you have a real nice tractor there.
  2. W

    NAA oil

    What oil do you use in the trans, hyd., and rear end? where do you add it and how full Thanks
  3. W

    8450 trans

    The place i work for bought it at a auction without looking at it so i know no history it trys to pull in 1&2 but just slips little or no noise when you go from 4 to 3 it will clunk like it has a lot of play in someting I think it pulled a small scraper pan and we bought it to pull a constrution...
  4. W

    8450 trans

    I have a 8450 with a quad range trans it's missing 1st&2nd gear in all ranges reverse seems fine all adjustments seem right I pulled the cover off the trans and don't see any bad gears could this be a simple problem or will i need to split it and dig deeper TIA Warren
  5. W

    Need help 4020 clutch

    Thank you for the help got a new one on order
  6. W

    Need help 4020 clutch

    Are there any tricks to changing the sleeve?
  7. W

    Need help 4020 clutch

    I'm putting a new clutch in a 4020 with syncro range trans the throwout bearing gave up and wore the fingers out on the engine clutch. I installed the new clutch and adjusted the fingers with the JD gauge.when i went to install the throwout bearing it just doesnt seem right.The sleeve that comes...
  8. W

    4430 clutch

    Thank you all for the info I will have to take my gauges and fittings out and check pressures on it. I was told all the hyd. worked fine and the pto was running the bailer with no sliping
  9. W

    4430 clutch

    I have not checked the pressure. Would there pe a port on the valve on the left side under the cab and what should it read ?
  10. W

    4430 clutch

    I"m working on a 4430 with a QR trans that won"t move. how do you tell if the engine clutch is slipping or if it is in the trans clutch unit? It trys to move in gear but won"t pull. Its been used for bailing and the guy running it told me he runs in D1 and just pushes the clutch in when the...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top