(800) 853-2651
SHOP NOW

Recent content by welderdude

Yesterday's Tractor Forums
  1. W

    weight

    what dose the front slab weights weigh about 2" thick 18" x 16" or so
  2. W

    John Deere G

    same computer wrong guy .
  3. W

    Unstyled block verus Styled block

    some us blocks can go 5 7/8 but it would have to be straight and round in the casting .5 3/4 is good on all blocks. 8" with the right rod combo.
  4. W

    unstyled v.s. styled crank??

    I did a 36 A and it went all right the pistons were the biggest problem . THe top ring will be right at the taper in the block so i welded a steel ring in the top ring land to take up the space . Used .045 M&W's from triple G it runs good good for stock antique . It might have 40 hp haven't had...
  5. W

    Unstyled block verus Styled block

    On what tractor A , G , F20 , WC ?
  6. W

    295 plow on a H

    Ill try this here to dose anybody have or seen a 295 mounted plow on a H i would like to put it on mine .Any help in what to look for at the case ih dealer ?Thanks
  7. W

    marvel schebler #21 carb floot

    The carb is on a 3020 we shaved it and its not hollow its on the tractor thanks
  8. W

    IH 295 plow and an H

    Dose or has any body seen an H with a 295 mounted plow on it Or have a picture ? i found a plow and with an H just sitting there it could just as well be on it . Is this type of plow ment to be on an H ? Never seen one on an H in southeast Mn .
  9. W

    marvel schebler #21 carb floot

    What dose a person do for the floot on a #21 carb . It has an after market one in it now and it has about 1/4 to 3/8 movement . I found a JD factory one but the guy said no deal ! This unit looks to be hollow so theres no shaving it to fit . I hate to spend $96.30 for another and get the same...
  10. W

    51 A main bearings

    I took the crank from an older tractor and it has shims i will use these . but need shells .
  11. W

    51 A main bearings

    Dose anybody know of or have a set of .010 under main bearings ? The owner of the crank took it to a shop to have it polished it came out of a junker and they took it apon them selfs to grind it .020 and .010 . i fuond rod bearings but looking for mains . Any leads would help. thanks
  12. W

    3 pt parts

    Where is the best place to buy the latch parts for the three point arms on a 1650 ?
  13. W

    new pulling magazine

    Is this gonna turn out like OLD POWER PRIDE i never got all my issiues from them . It was a good mag with some fun looking build ups . still have them fun to look back on.
  14. W

    octane ratings

    Timeing is dead center on the impulse mark on the flywheel.I just went and got 10 gal of 110 and will blend it .
  15. W

    octane ratings

    Timing is on top dead center i will drop that back to . the tractor has never had to run more than a little bit at a time . ive never had it on a full out workout unless its on the track . Ill try to find some 100 .
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top