(800) 853-2651
SHOP NOW

Recent content by willyj

Yesterday's Tractor Forums
  1. J

    scrap metal prices?

    anyone know of a online site to get current scrap metal prices ,I took in 4 loads yesterday and got $150 a ton, today I got $130
  2. M

    DavidP SouthWales

    Yes my tractor has pressure control From what I have read on hear I think there is a position control spring broke in it I just made room for it in my shop I have IPTO Do I have to split my tractor or can I take the lift cover off Thanks
  3. G

    hydraulics/loader

    I just bought my first tractor a 47' 8n with a freeman loader. The hydraulic line running to the loader has a spin valve like an outside faucet to open and close the line. You have to open the line to use the loader, however to do this the old owner also had chains wrapped around the arms of...
  4. C

    601 Ford Hydraulics

    I have just become the owner of a 1957 601 Ford. Transmission fluid has to be changed pronto. Is the transmission, rear end and hydraulics all the same fluid like an 8 N, also what type of fluid. GL-1 for the 8 N. Also manual No. for this series tractor. Same message posted on Tractor Talk...
  5. W

    identify tractor

    can anybody tell me what year this tractor is
  6. D

    Hey Farmall H guys

    What fans are you running on your H's if you aren't running electric? Is there a flex fan or one that doesn't throw near as much air as a stock one? Mine really throws a lot of air too much actually. I would imagine there are a few ponies hinding in there somewhere. Thanks for your advice!
  7. A

    mystery tractor

    I only got one picture on the first post here is the second
  8. A

    1650 Transmission Problem Fixed - Thank you all !

    Thanks for all the advice on trying to figure out why my 1650 transmission was locking up between low and high ranges when you would slip it into the high range. The input shaft was the culprit. The shaft itself was good but I didn't have enough shims installed on the front side of the bearing...
  9. J

    boring an F140 MH 22 engine

    I have a brand new set of 3-5/16" pistons & rings that I would like to put in my old worn out F140 engine. That will require boring it 1/8" over stock. Has anyone done this? I'd just like to know if anyone has done it before I screw up a block un-necessarily. Thanks for any help.
  10. O

    H Cooke

    Hey the new at 6pm said you where getting a lot of snow down your way as in 12 plus inches. So you keeping your head above all that cold wet stuff and keeping things warm?? News also said a bunch of roads down there where closed and little if any thing was moving.
  11. C

    AC-G piston rings

    got in a mess tonite putting in new rings and pistons when i of my oil rings broke were will in find rings for 1 piston thanks cdv
  12. F

    unstyled WC fenders

    I am in the process of manufacturing fenders for the early WCs. They have turned out so well, we decided to make them available. We have the manufacturing and laser capabilities to do produce these better than the originals. I am looking for feed back at this time. How much interest is out...
  13. R

    OT: Dodge diesel steering problem

    My 99 Dodge diesel power steering has always moaned and groaned when cold and the temp outside is below 30F. The other day it got worse and fluid started foaming out the filler cap. I refilled it and it did fine until the next morning. The pump also runs the brake hydro-boost system. I replaced...
  14. M

    JD 830 German 3 cyl. rear main and clutch

    I am getting ready to split the tractor to replace the rear main seal. Looks pretty straight forward on the split. Figured even though the clutch does not seem bad I will look at close and possibly replace. Question is can I get that seal out after dropping oil pan or does it just pop out after...
  15. A

    Ford LT8 Lawn tractor

    I was given this mower and it works great, until the blade belt broke. Anyone know how to route it or any suggestions?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top