(800) 853-2651
SHOP NOW

Recent content by wyss

Yesterday's Tractor Forums
  1. D

    Need a new zero turn, huge decision, lots of cash requir

    Hi folks, I know this is not a garden tractor question but I've looked over this forum and seems like a lot of sensible answers here. I need a new zero turn mower. I'm looking at 52-54" decks. A dealer is pushing me toward ferris IS 600 52" due to the suspension. (ride is important to me)...
  2. K

    Tea20 Governor plunger rod spring.

    Hi Clarification please, in my manual it states that governor springs fitted to Tea20 were of 15 coils. I have not come across any on any Tea20. They all seem to be fitted with the 26 coil spring. What was the reason behind the two different springs??
  3. J

    530ck spindles

    I may need to replace the spindles due to someone having attempted to weld them together because of wear. I bought one new knuckle and the splines on it are much better than the old ones so maybe I'll be ok. The concern I have is that my spindles measure much differently than the ones they offer...
  4. D

    Front rope seals

    Hello everyone. I just recently rebuilt the engine on my ford 9n.( my first engine rebuild ever). I got lots of information from these forums and I want to say thank you to everyone for all the help! Anyway I got the engine back in the tractor and was running it around yesterday for about an...
  5. C

    Using washing machine tubs as work stools while working on

    At a local tractor repair shop I saw them using upside down washing machine tubs as work stools while working on tall equipment. Though it was a good idea to pass along.
  6. grandpa Love

    Stuck Kubota

    Our preacher called yesterday morning and asked if we could bring a tractor over and pull his out of a "little muddy spot". Apparently his daughter drove the 4 wheeler in to the mud and got stuck, so, having a 4 wheel drive tractor he drove right in to push her out...... 4-5 hours later it got...
  7. jon f mn

    Today's funny

    .
  8. F

    Massey Ferguson MF20 3 Point Hitch Lift Weight Lift

    What is the 3 point hitch lift weight capacity on a Massey Ferguson MF20?
  9. grandpa Love

    No church road trip

    No church today. Power still out for miles around from hurricane Zeta. Saw this on Facebook market place. Late last night. 75 miles away. He is holding it for me. It's fairly cheap. Has the radiator and sheet metal. " ran a year ago, needs carb cleaned" we will see. We headed out! Thoughts on...
  10. D

    Cost of plastic buckets

    Cost of buckets must be going up, this week's Fleet Farm ad has engine oil in a cardboard box. Mystic 15W40 6 gallons in a "GoBox" for $50 after rebate. Hydraulic oils too. Does look kind of handy, and I really don't need any more buckets. I'll try a couple.
  11. B

    1085 pto parts help

    Good morning all! New here first post. Im needing some help finding some parts for the output part of this 1085. My mothers husband passed and he used it to mow their property. I know nothing about it but its now my chore to do the mowing with the tractor. Upon walk around I noticed whats is...
  12. 1

    Help troubleshooting mf135 power streering

    MS135 1968 continental gas with allied FEL. On the ground will turn easily to right almost impossible to steer left. off the ground will turn both ways but a little resistance to turning left. Is this the power steering column valve that's gone bad? Dealer reluctant to repair since "steering...
  13. B

    Fuel Tank Filler Neck Straightening Tool on a WD45

    Does anyone know if the Steiner Tractor ABC2672 Fuel-Tank-Filler-Neck-Straightening-Tool will work to straighten filler neck tabs on a WD45 fuel tank? Even better does anyone know where I can rent this tool rather than paying so much for a one time fix?
  14. J

    New thermostat for 630

    I am replacing the thermostat on my 630. Do I need to use some type of adhesive or sealant to hold the new thermostat in the housing? The old thermostat looks like it was held in by some type of adhesive, and the service manual is pretty vague on installation.
  15. M

    New member

    Hello everyone, I am the proud owner of a 1952 Ford 8N tractor that I hope to get into good working shape. I will be reading the forums and hoping to learn a lot from you old and young pros out there.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top