Power steering pump Ford 4000

So I just opened the PS reservoir on my new to me 64 4000 and noticed some things were missing. Here’s a nice pic. I’m pretty sure I’m SOL and will have to run it this way. I know I can buy a filter, make a retainer, but the filter support is no where to be found online and I’m not going to drop any cash on a rebuilt pump. If anyone has any leads for that filter support let me know but I just wanted to share this along with my pain.
 

Attachments

  • IMG_0462.jpeg
    IMG_0462.jpeg
    2 MB · Views: 0
So I just opened the PS reservoir on my new to me 64 4000 and noticed some things were missing. Here’s a nice pic. I’m pretty sure I’m SOL and will have to run it this way. I know I can buy a filter, make a retainer, but the filter support is no where to be found online and I’m not going to drop any cash on a rebuilt pump. If anyone has any leads for that filter support let me know but I just wanted to share this along with my pain.
It is a nce pic, but it doesn't give me much information regarding parts that are missing (and not in the picture.)

I'm assuming that your tractor is some version of a 1964 4000 series tractor. They all seemed to use Eaton pumps, but the parts inside the reservoir varied with the exact model. There is some hope for finding replacement parts. Ford cars and trucks of that era also used Eaton power steering pumps. Some aftermarket parts are available to antique car and truck fans. It is likely that Ford used the same parts for tractors as they used for cars and trucks. If you could find a decent picture of the "filter support" you are seeking, you might find the aftermarket car equivalent on a website like

 
It is a nce pic, but it doesn't give me much information regarding parts that are missing (and not in the picture.)

I'm assuming that your tractor is some version of a 1964 4000 series tractor. They all seemed to use Eaton pumps, but the parts inside the reservoir varied with the exact model. There is some hope for finding replacement parts. Ford cars and trucks of that era also used Eaton power steering pumps. Some aftermarket parts are available to antique car and truck fans. It is likely that Ford used the same parts for tractors as they used for cars and trucks. If you could find a decent picture of the "filter support" you are seeking, you might find the aftermarket car equivalent on a website like

Here are a couple pics of the parts I’m talking about. The diagram shows all three and the picture shows the filter support. I’ve been a little confused because, like you mentioned, I’ve seen the same pump with a slight difference in internal components. I have the service manual and it calls for one set of parts for then industrial tractor, which I have, bs the general purpose tractors. Well what the manual says doesn’t match what messicks says for the same 4130 tractor. Anyway, thanks for the tips on the car and truck PS pumps. I’ll dig around there and check out your link.
 

Attachments

  • IMG_0482.jpeg
    IMG_0482.jpeg
    174.3 KB · Views: 0
  • IMG_0483.jpeg
    IMG_0483.jpeg
    313.8 KB · Views: 0
tractor-part.com is a search site for a number of tractor salvage yards across the country. It shows that Wengers of Myerstown in PA has that filter support in stock. You might try giving them a call.
 
Here are a couple pics of the parts I’m talking about. The diagram shows all three and the picture shows the filter support. I’ve been a little confused because, like you mentioned, I’ve seen the same pump with a slight difference in internal components. I have the service manual and it calls for one set of parts for then industrial tractor, which I have, bs the general purpose tractors. Well what the manual says doesn’t match what messicks says for the same 4130 tractor. Anyway, thanks for the tips on the car and truck PS pumps. I’ll dig around there and check out your link.
The filter sets on the round lipped base that exists in your pump. You will likely find this thread interesting as it shows a solution for your missing retainer. https://forums.yesterdaystractors.c...-power-steering-filter-retainer-work.1619217/
 
The parts you are looking for are tractor only . All the later tractors are the same , however early Heavy Duty Industrial 1958 / 1959 were different . Car and truck parts are different also .
I poked around a bit and couldn’t find anything. Thank you for clarifying.
 
The filter sets on the round lipped base that exists in your pump. You will likely find this thread interesting as it shows a solution for your missing retainer. https://forums.yesterdaystractors.c...-power-steering-filter-retainer-work.1619217/
That base is completely missing in mine. I just ordered it from Wengers, from the link Sean in PA sent, along with a filter and random gaskets for the loader and tractor today.

I appreciate the link! I’ve seen a couple other threads here and on another forum where people have made their own retainer but this one takes the cake. I definitely going to copy this one. Thank you!
 
I have another question about this power steering pump(1963 4000 Industrial 4cyl gas). I replaced the seals between the reservoir and the pump and it still leaks. I think it's the main seal and probably others. The process to put new seals seems pretty straight forward, but I have no idea which kit is correct. It is an eaton pump and has these PN in the casing below the reservoir behind the pulley... 252N. Can't tie that down to a specific PN so that I can get the correct kit. I am looking at these kits and think the Walt's is correct, but I have other things to order from Yesterday's TRactor so I rather get the correct kit from them...

1.
https://link_disallowed/acatalog/UF01300---Power-Steering-Pump-Kit---66579-70608.html#SID=9685
2. 3.
Also, I notice that the pump doesn't lock down on the mounting bracket. It moves left to right quite a bit. Is this normal? It seems I'd have to deform the mounting bracket to get it to not move and there is not enough room to add a washer in there. Any idea? Thank you!
 
I have another question about this power steering pump(1963 4000 Industrial 4cyl gas). I replaced the seals between the reservoir and the pump and it still leaks.

I had (and sill have) the same issue on my 1955 960. People say that if someone (previous owners) over torqued the part that holds the reservoir to the pump it will warp the bottom of the reservoir. The rectangle section seals ( O rings) will not make a good seal. On my tractor you could see the top of the pump was wet. This seemed to be higher than any other seals. My solution was to empty the reservoir, remove the PS belt, and park the tractor while I pondered the problem. I suspect the problem will outlast me!
 
I have another question about this power steering pump(1963 4000 Industrial 4cyl gas). I replaced the seals between the reservoir and the pump and it still leaks. I think it's the main seal and probably others. The process to put new seals seems pretty straight forward, but I have no idea which kit is correct. It is an eaton pump and has these PN in the casing below the reservoir behind the pulley... 252N. Can't tie that down to a specific PN so that I can get the correct kit. I am looking at these kits and think the Walt's is correct, but I have other things to order from Yesterday's TRactor so I rather get the correct kit from them...

1. 2. 3.
Also, I notice that the pump doesn't lock down on the mounting bracket. It moves left to right quite a bit. Is this normal? It seems I'd have to deform the mounting bracket to get it to not move and there is not enough room to add a washer in there. Any idea? Thank you!
I tried to see what the kits you listed might fit. I have no idea what #1 is or what it fits.
Numbers 2 and 3 listed information that could be looked up on a CNH parts website. The part numbers for items ion the kit or for the pump model number which the kit would fit seem to show that both kits are for later 3 cylinder tractors.

The parts diagrams don't clearly show how the pumps are mounted to the brackets on your tractor. However, they clearly show that lock washers are used on the row crop models. The diagrams for the 4000 row crop models looks like my earlier 960.
1793173831513.png
 
I have another question about this power steering pump(1963 4000 Industrial 4cyl gas). I replaced the seals between the reservoir and the pump and it still leaks. I think it's the main seal and probably others. The process to put new seals seems pretty straight forward, but I have no idea which kit is correct. It is an eaton pump and has these PN in the casing below the reservoir behind the pulley... 252N. Can't tie that down to a specific PN so that I can get the correct kit. I am looking at these kits and think the Walt's is correct, but I have other things to order from Yesterday's TRactor so I rather get the correct kit from them...

1. 2. 3.
Also, I notice that the pump doesn't lock down on the mounting bracket. It moves left to right quite a bit. Is this normal? It seems I'd have to deform the mounting bracket to get it to not move and there is not enough room to add a washer in there. Any idea? Thank you!
I searched for 'Eaton power steering pump rebuild kit ford tractor' and found a kit at two of YT's competitors- maybe a phone call to our host here would find that they sell a similar kit. If not, then DC or Stnrs offer it.
 
I searched for 'Eaton power steering pump rebuild kit ford tractor' and found a kit at two of YT's competitors- maybe a phone call to our host here would find that they sell a similar kit. If not, then DC or Stnrs offer it.
I was looking at NH's and Messick's diagrams and noticed that the pump was not called out, but after staring at the list for a while I realized the pump was listed without a call out. Found this PN for it: C0NN3A674F. I am just going to assume this is the same pump that I have (pretty sure my machine is a bit Frankensteined) and just order a kit for it which I found here:https://www.wagneragsales.com/ProductDetails.php?ProductCode=ABC3275&CartID=1
 
Last edited:
I have another question about this power steering pump(1963 4000 Industrial 4cyl gas). I replaced the seals between the reservoir and the pump and it still leaks.

I had (and sill have) the same issue on my 1955 960. People say that if someone (previous owners) over torqued the part that holds the reservoir to the pump it will warp the bottom of the reservoir. The rectangle section seals ( O rings) will not make a good seal. On my tractor you could see the top of the pump was wet. This seemed to be higher than any other seals. My solution was to empty the reservoir, remove the PS belt, and park the tractor while I pondered the problem. I suspect the problem will outlast me!
Thank you for the tip. I'll make sure to take good look at the interface between the reservoir and pump when I take it off to change the seals.
 
I tried to see what the kits you listed might fit. I have no idea what #1 is or what it fits.
Numbers 2 and 3 listed information that could be looked up on a CNH parts website. The part numbers for items ion the kit or for the pump model number which the kit would fit seem to show that both kits are for later 3 cylinder tractors.

The parts diagrams don't clearly show how the pumps are mounted to the brackets on your tractor. However, they clearly show that lock washers are used on the row crop models. The diagrams for the 4000 row crop models looks like my earlier 960.
View attachment 168154
Are you saying lock washers are used where the pump mounts on this bracket? When I bought my tractor it only had(and still has) only one bolt to mount it without any kind of nut on the opposite end of the bolt. It just threads straight into the bracket. I don't think this is the way it was intended, but even if I got a longer bolt with a nut, the pump would still be loose between the two ears of the bracket.
1793299283972.png
 
Are you saying lock washers are used where the pump mounts on this bracket? When I bought my tractor it only had(and still has) only one bolt to mount it without any kind of nut on the opposite end of the bolt. It just threads straight into the bracket. I don't think this is the way it was intended, but even if I got a longer bolt with a nut, the pump would still be loose between the two ears of the bracket.View attachment 168335
I was copying a diagram (which I thought might be helpful) for a 4000 row crop tractor.

The one below is for an industrial. Your latest picture shows the "Bracket, pump support (part # 86513520) which is used on both the row crop and industrial tractors. The parts list associated with the diagrams suggests that the following should be used with both.

1793318001930.png

My tractor is 100 miles away, and I haven't tinkered with it for a couple of years.
 
I was copying a diagram (which I thought might be helpful) for a 4000 row crop tractor.

The one below is for an industrial. Your latest picture shows the "Bracket, pump support (part # 86513520) which is used on both the row crop and industrial tractors. The parts list associated with the diagrams suggests that the following should be used with both.

View attachment 168352
My tractor is 100 miles away, and I haven't tinkered with it for a couple of years.
1793318904611.png
 
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top