(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. G

    Magneto for a Cletrac F

    I am looking for a magneto for a Cletrac F. I have a Wico C mag that needs work and I don't think that is the correct mag anyway. What is the correct Mag and where can I get a good rebuilt one. Thank You, Gary
  2. G

    4610 Steerring leak at pitman arm

    My 4610 has oil seeping from the pitman arm. The parts manual shows two "seals" which I think are orings inside and 2 felt seals on the outside of the housing. Once the pitman arm is removed, is it possible to replace the orings without removing the steering shaft? Thank You for ideas.
  3. G

    4610 Gauge Cluster Question

    I have a 1984 4610 with original gauge cluster. When running, the fuel gauge flickers and when I turn the key to off, the battery light does not glow as it should, I checked and cleaned all wires and terminals on back of cluster grounded the sender and got full gauge travel but when running it...
  4. G

    8N Axels too long?

    I am working on a 12/51 8N. The axels have been shortened to 26 7/16". I think the original axels were cut and re splined to get to that length. Before I started working on it, I rocked the rear wheels and had play of around 1/8-1/16". I could hear a "thunk" each time I rocked the wheels...
  5. G

    8N Accessories?

    I just got an 8N Dec 51, I think. There are a few things I am not too sure about which came with it. Air Precleaner, Harco or Cyclone, Not sure what I have. Seat, Pan seat but has 2 rubber bumpers in back and a different suspension than I am familiar with. Battery cover, A sheet metal...
  6. G

    Radius Rod Socket 4600SU

    How much play should there be on the ball end of the radius rod? All the parts look ok, nothing looks too worn but when it is up on jacks and I pivot the front axel up and down I can see movement and hear the metal to metal play on the ball and sockets. Thank You, Gary
  7. G

    4600 Part Number Question

    I am looking for a power steering pump for my 1978 4600. The original pump # is D8NN3K514EA. Looking on this website I can find a part #E6NN3K514EA Are they the same? I also have a 4610 with Pump # E0NN3K514CB would these all work with the pump I see on YT which is the...
  8. G

    Ford 4600 Power steering cylinder

    I have a 1978 4600 with 1/2" rods on the factory power steering cylinders. They are getting scratched so I think I may need to buy new ones. Can I go with the 5/8" rods? or should I stick with 1/2"? Thank You, Gary
  9. G

    3000 imput shaft seal replacement

    I have been reading threads on this board but have not seen any follow up to this question. I have a 1974 ford 3000 with 8 speed transmission. 4 -hi 4-low. 2 stage clutch, input shaft has 10 splines pto input has 29. I am replacing the clutch, pressure plate, throw out and pilot bearings as...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top