(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. W

    In need of 24T baler chain information

    I once had a website where you could be 24T parts including chain kits but I cannot seem to find it now. My chains are in need of replacement but I cannot remember what chains the 24T baler uses. Does anyone have any information on what chains I need for a 24T? Your help is appreciated!
  2. W

    Oil leaking from front of transmission - delete pump

    My H was leaking gear oil from the transmission since I bought it. I bought the seals and settled in to replace them. I pulled the dust cover off and found that the pump driveshaft was gone. What was worse, the female drive coupler on the transmission side was also missing. (The coupler...
  3. W

    73 656 Diesel Starting problem

    I have a 1973 656 with D282 diesel. When I press the start button to turn over the engine, the starter makes a noise and it won't turn over the engine. This was happening rarely and now more often than not. If I repeatedly press the start button, it will eventually engage and when it does...
  4. W

    International 656 Utility Diesel rear end gear oil

    Hi All, We recently moved and I don't know where I packed by 656 manual. Does anyone have an electronic copy or can anyone remind me how to check the gear oil in my tractor? And what weight is it supposed to be? It's a 656 Diesel Utility tractor - gear drive Thanks in advance, Bill
  5. W

    NH 455 sicklebar mower

    I just purchased a NH 455 sickle bar mower for $150. The mower works great but grass gets caught in the hole where the last knife goes through the shoe at the end of the sickle bar. Over time, the grass bunches up and lifts the bar off the ground. It looks like it's missing a part as there...
  6. W

    640 starving for fuel after getting hot

    Bought my 640 and didn't use much for work until now. After the engine is hot (after using 15-30 mins bush hogging) the engine starts to starve for fuel. When the issue is happening, if I pull out the choke 1/2" or so the engine will settle down, which leads me to believe it's gas related...
    • wfd2
    • Thread
    • Replies: 9
    • Forum: Ford
  7. W

    656-D Utility water in transmission hydraulics

    Hello, I have a '73 656 diesel utility w/standard transmission. In one of my costly forgetful moments, I neglected to put the dipstick back into the transmission after using my post pounder. Oh, and it rained on/off for a few days before I found that the oil filler tube was open. I am sure...
  8. W

    Workmaster 641 electrical system

    I have recently acquired a 1959 Workmaster 641. The battery that was installed (and still is) is clearly a 6V battery. However the system is a negative ground. I thought the 6V systems are positive ground and the 12V systems are negative ground? Where there negative ground systems? And...
    • wfd2
    • Thread
    • Replies: 11
    • Forum: Ford
  9. W

    Work Master 601 starting problem

    I have a starting problem with my "59 Work Master 640. Battery is charged. Press start button and solenoid clicks. Sometimes it will "catch" and turn over engine...but when I release the starter button it continues to crank on its own (even when ignition switch is off). I tried removing the...
    • wfd2
    • Thread
    • Replies: 4
    • Forum: Ford
  10. W

    656 diesel won't start after it was running great all day

    I have a "73 656 diesel that I was using yesterday just fine. Ran great until I shut it off for about 15 minutes to take a break. I attempted to start it again and it sounds like it"s not getting fuel. This has never happened before and this engine has been easy to start for me in the 3 years...
  11. W

    H driveshaft seals

    My '47 H is leaking gear oil pretty bad. It's coming out of the area around the clutch inspection cover. Looks like the driveshaft seals for the driveshaft and hydraulic pump (?) is leaking. It looks like I can remove the ujoint bolts, slide out the drive shafts and put the seals in that way...
  12. W

    Weight of a IH 2000 loader

    Would anyone happen to know the physical weight of the IH 2000 loader? Thanks in advance, wfd2
  13. W

    Fuel shutoff leaking on Workmaster 641

    Uncovered my Ford this morning only to find my fuel shut-off leaking. (Figures, I just put gas in the tank when I parked the tractor.) Does anyone know if this shut-off valve be repaired (replace inside o-ring, etc) or do I need to buy a whole new valve? I'd rather not have to pull the...
    • wfd2
    • Thread
    • Replies: 7
    • Forum: Ford
  14. W

    Wiring diagram for '59 Workmaster 601

    I found some old links for electrical diagrams for a '59 601 Workmaster but most no longer work. Does anyone have a current link? It is a stock 6v positive ground. Thanks in advance for your help!
    • wfd2
    • Thread
    • Replies: 3
    • Forum: Ford
  15. W

    601 Workmaster dash light question

    I just bought a '59 601 Workmaster. On the dash, there is a little red light that sometimes comes on (at lower RPM). Is that light an idiot light stating that the genny isn't fully charging the battery? Or something else? It's still all stock, on a 6V pos ground. Your help is appreciated!
    • wfd2
    • Thread
    • Replies: 12
    • Forum: Ford
  16. W

    Mounting Shaver HD-10 on 656, Part 2: Hydraulic lines help

    Ok, I got the Shaver post driver on the 656. All connects up mechanically. Now for the interesting part. The HD-10 I have has what looks to be a 1/2" pressure line (and fitting) with a 1" return line (to be put directly into the hydraulic tank). Problem is the pressure line (make end)...
  17. W

    '73 656D help with Shaver and tractor hydraulics

    I just purchased a Shaver HD-10 post driver for the back of my 656. I have two remotes on the 656. One is running my front loader and the other is open. I"m going to use the open remote for the driver. There is a pressure line (smaller diameter hose and a bigger line (1" diameter hose) on...
  18. W

    3010 USX 21 carb diaphragm needed

    My friend has a 3010 with a MARVEL SCHEBLER USX21 carbuerator. The diaphragm in the carb is shot and I can"t seem to find a new one for him on the web. Does anyone have any leads on where I can get this diaphragm? Thanks in advance! Bill
  19. W

    Danuser TD-1 Post Driver

    Hello and Happy New Year! I just purchased a Danuser TD-1 post driver that is mounted on it"s own trailer. It"s run by a 3HP B&S engine, not a PTO. I believe it"s from the early 60"s. Does anyone have a copy of an owner"s manual for this unit? Does anyone have experience with this unit? If...
  20. W

    3 pt hitch will not lift on my 8N

    My 8N's 3 point hitch stopped lifting last weekend. I just purchased this tractor this year for brush mowing, so I'm not quite familar with it's 3 pt system. Could this be something simple like a check valve or something more major like a pump? The tractor runs fantastic and the PTO works...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top