(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. O

    Looking for a junk schwitzer 3lm or exhaust housing

    Looking for a junk schwitzer 3lm or exhaust housing
  2. O

    Looking for a junk 3LM turbo or a exhaust housing

    Looking for a junk 3LM turbo or a exhaust housing.
  3. O

    3LM exhaust housing size?

    Does anyone know the exhaust housing size in CM"s on a 3LM turbo?
  4. O

    Farmall M more power

    completely rebuilding my 1941 M, got a ground crank "the late crank" rods all in spec and sized with the pins. Have the Red Power 4inch overbore kit with step head pistons ready to be put together. Wondering what else i can do to get more hp, looking to try to get 60+ hp.
  5. O

    Ford 401 puller valve springs

    Does anyone know a good heavy valve spring i can run in my Ford 8000 puller? Running 3200rpm, doing a valve job after i blew my head gasket.
  6. O

    Ford 8000 coolant problem possibly head or head gasket issue

    Well guessing I am going to be beared with bad news or even worse bad news. I recently dropped a used motor that ran good in my Ford 8000 due to the old one not running great and puked blow by. I have been noticing a low level of coolant and added 2 qrts of water to it a month ago. Today I...
  7. O

    Ford 8000 charging system

    I just put a brand new single wire alternator on my tractor and brand new interstate 4dlt battery and i am making no charge and it does not keep a charge it"s like if I leave it over night it"s dead
  8. O

    My ford 8000 pulling

    http://www.youtube.com/watch?v=48a94n20fiE
  9. O

    ford 9600 or 9000 grille

    looking for a ford 9000 or 9600 grille
  10. O

    ford 8000 flywheel torque

    what are the torque specs on a ford 8000 fly wheel bolts?
  11. O

    Ford 96-8600 step

    Does anyone have a right hand step for a 9600 or 8600 ford? I am looking for one to buy one.
  12. O

    old style wheel center shim on 8000

    on the old styled wheel center power shift style rim on the 8000 how do you take off the rim? Do you loosen the big jam nut on the shim?
  13. O

    8000 rim swap for bigger rim question.

    I bought a set of 20.8 tires and now need bigger rims. I have an early 8000 with power shift rims, 8 bevels. Now my question is will a power shift rim off of anything ford, allis etc fit if it is a power shift rim with 8 bevels?
  14. O

    8000 back up and running

    Took my head off lapped the valves replaced a bent push rod and new air cleaner and new head bolts. all of this made it start a bit easier then before and is deffenantly throatier! But Im thinking I have a bad set of injectors. Smokes a LOT of white and black cold started and doesnt want to rev...
  15. O

    Turbo Precleaner

    Does any one have a 4inch Turbo pre cleaner they would sell me?
  16. O

    Turbo Precleaner

    Does any one have a 4inch Turbo pre cleaner they would sell me?
  17. O

    Turbo Precleaner

    Does any one have a 4inch Turbo pre cleaner they would sell me?
  18. O

    swapping a 9600 engine

    This message is a reply to an archived post by fordsrock on September 18, 2012 at 12:43:20. The original subject was "swapping a 9600 engine". the 86 one will bolt up, new one has a 8 bolt fly wheel, you need the 6 bolt. Also the top bolts for mounting the engine to the transmission do not...
  19. O

    swapping a 9600 engine

    This message is a reply to an archived post by RodInNS on September 18, 2012 at 14:11:02. The original subject was "Re: swapping a 9600 engine". will not work unless you modify the front end and get a tw series oil pan. I tried this with my 8000 and the oil pump was my hang up and i did not...
  20. O

    Ford 8000 hard start and wont rev after sitting

    I am having starting problems with my 8000. I have lapped the valves, making good compression. Have a tw35 injection pump 9600 intake holset turbo and injectors are in good shape. New life pump, fuel filter housing and fuel filters. It starts hard and when you get it started it is not firing on...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top