(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. 1

    Oliver green SEMI gloss paint

    Recently picked up a tractor thats painted a lighter green than it should be. I'd rather use a semigloss paint not the standard gloss paints. I want to use a decent quality of paint but have been told that adding enough deglosser/flattening agent will weaken the paint. Ideally, whatever I spray...
  2. 1

    Clev Motor Plow mod R-need copy of parts book & user man

    Starting work on my model R and am looking for any parts books or instruction manuals for that model.. Anybody out there have such a thing? Also looking for brochures or advertising with pictures.. Thanks
  3. 1

    How do I get this belt pulley off shaft?

    There is nothing to grab onto on the center hub. The pressed cardboard pulley only has a thin metal plate on the front and rear which I dont want to pound on. I'm unfamiliar with this type and cant figure out how to use a puller to pull it off the shaft. This hercules engine was on a JD...
  4. 1

    Need .045-.060 over 4.0 pistons, 2.75+ comp. height

    Looking for 4.045--4.060 Pistons, rather tall in compression height at 2.75"-2.85" Wrist pin, 1.125" They can be alum or cast iron.. This is for a Wisconsin water cooled 6 cyl. If figured this would be the place to post as this group seems to be quite creative.... Thanks!
  5. 1

    Need key for this Eisemann CAT ignition switch

    Need a key for this. I have another similar one that does take a double "tooth" key with an oval tab but this one looks like it might be some sort of knob with peg/shaft and single tooth. Anybody out there have one that fits and can email or answer back here with a picture? Roland...
  6. 1

    Anyone know the compression height on a Super M piston?

    1) what is compression height on the standard flat top piston? 2) do they come in a 4.030 or 4.045 diameter? Thanks, Looking to use these in another engine that needs a 2.75"---2.85" compression height
  7. 1

    Looking for oddball 4.045 diam. flat top piston

    Looking for pistons to rebuild a vintage 1928 6cyl low compression engine....the problem is the compression height of 2.75---2.85" It looks like some of the John Deere pistons might work. Yes, I've called all the major piston manufactures and nobody has anything that "tall". Farmall, Alice...
  8. 1

    Need help with big Wisconsin engine info.

    Figured I'd give you guys a shot at this because it appears the stationary engine group has some knowledge of Wisconsins. This is a big 1929 4"bore x 5" 6cyl model H engine with overhead valves. I've got 2 of these to rebuild one which is a power plant and one in a crawler. Neither engine is...
  9. 1

    Looking for Oliver 550 or 55 Super on West Coast

    Looking for a very good to excellent restored OLIVER 550 or 55 Super out here on the west coast, southern WA, Oregon or northern CA email or PM me.. Thanks
  10. 1

    Need operators/instruction manual for Cletrac 30B

    For Cletrac 30B, I need an operators or instruction manual. I already have a parts book Anybody out there have one they want to part with??
  11. 1

    Need width dimensions of Oliver 78 2 bottom plow

    I'm hoping to pick up the Oliver 78 plow I purchased recently and want to transport it in the bed of my F150. Anybody out there have one that could give me hub to hub width dimensions or good pictures?? Thanks
  12. 1

    Need Marvel Schebler help for 275 cub inch engine

    I"ve used the TSX series before and like them because they"re simple and work. I need one with a 1-5/16" max throat and that can feed a 1400 rpm max, 4" x 5.5"" stroke 4 cyl engine. I used a TSX-813 before. Any other suggestions? Is there a master spec manual that shows engine size, throat, and...
  13. 1

    Main bearing shell modification to reduce end play

    I"m restoring a 1918 Cleveland Tractor mod H crawler engine and want to reduce my .030 crankshaft end play to .002. Since NOS bearings are non existent my thoughts are to build up the forward shell flange of the front bearing as it is the most worn. The wear is coming from contact with the...
  14. 1

    What key goes in this Cletrac magneto switch??

    Can anyone out there show me what the key looks like that fits in this ignition/magneto switch??
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top