(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. R

    IH 3 bottom fast hitch plow identification

    Hello all, Can you all identify if this is a model 311 plow? I can’t find a badge on it anywhere. I don’t have the fast hitch arms bolted to it yet. Also, if anyone has an idea on where to find new coulters for it? Much appreciated. Robert
  2. R

    IH 560 diesel parasitic draw issue

    Good evening, I recently converted from 12v generator to 1 wire alternator on my IH 560. I was instructed to connect the field and Gen wires together on the “1 wire stud” on the alternator and then combine “field, Gen, batt & L” wires at the voltage regulator as it essentially acts as a...
  3. R

    New 6volt generator on Farmall B and 3 hours later battery has been killed.

    Good evening, Just received a newly refurbed 6 volt generator for my Farmall B (positive ground). Installed generator and connected old voltage regulator. Tested battery before starting and it was good at 6volt. Started tractor and tested battery again with multimeter and got good reading of...
  4. R

    IH 560 Standard/Wheatland Power Steering schematic

    Would anyone have or could point me to a link for a schematic showing an installed power steering set up on an IH 560 standard/wheatland? Appreciate any help. Even if you have one of these tractors with PS on it already, pictures would be very helpful. Thank you
  5. R

    McCormack 10 Drill settings

    Good morning, I’m going to be seeding some Milo for a friend with my McCormack 10 grain drill. He’s looking for 30” rows with about 2 - 3 lbs per acre. I’ve looked through the chart and can’t come up with a calculation for a setting on the drill to get to the 2 - 3 lbs per acre. Anyone by...
  6. R

    Farmall B hard starting

    All, Id appreciate any input on an issue Im having with my Farmall B. Battery is charged, new battery cables and new starter. I have had issues recently when cranking the engine it barely cranks it over. But it will eventually hit and start. I will preface that I just rebuilt the engine...
  7. R

    IH 560 Diesel Coolant question

    Good afternoon all, I'm still waiting form my service manual to arrive so thought I'd throw this question out to you. I replaced the radiator in my IH 560 Diesel as well as installing a frost plug heater into the engine block. Since I had to drain some of the coolant from the block when...
  8. R

    Valspar 4432-01 IH Red

    Good afternoon, I started painting my 1959 IH 560D Standard with Valspar 4432-01 IH Red. I painted the rear wheel hubs and the seat with it and really like the deep IH red. I've still got 1 1/2 quarts remaining and ready to paint the rest of the parts and the tractor. I'm afraid 1/ 1/2...
  9. R

    1959 IH 560D Wheatland

    Hello all, I purchased a 1959 IH 560D a couple months ago. It has several leaks on the fuel injection pump front and rear side. I planned to disconnect it and send it off to a professional shop to have it rebuilt. before I do, should I take note of or mark where the shaft is at prior to...
  10. R

    John Deere 70 Diesel Crank shaft repair

    A couple weekends ago my flywheel became loose. The locking nut was in poor condition, but the threads on the crankshaft are not too bad. However, after buying a new locking nut, I could not get it on without the possibility of screwing up the nut threads so the end of the crank shaft needs to...
  11. R

    John Deere 70 Diesel Crank shaft repair

    A couple weekends ago my flywheel became loose. The locking nut was in poor condition, but the threads on the crankshaft are not too bad. However, after buying a new locking nut, I could not get it on without the possibility of screwing up the nut threads so the end of the crank shaft needs to...
  12. R

    John Deere 70 Diesel Crank shaft repair

    A couple weekends ago my flywheel became loose. The locking nut was in poor condition, but the threads on the crankshaft are not too bad. However, after buying a new locking nut, I could not get it on without the possibility of screwing up the nut threads so the end of the crank shaft needs to...
  13. R

    JD 70D pony motor clutch not engaging flywheel

    I also have a 70D, in the recent past when engaging the control lever, there would be a grinding noise and I might have to re-engage a couple times before I would see the flywheel start moving. This past weekend, the pinion gear would not engage at all. I took off the flywheel cover and could...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top