(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. V

    Massey Ferguson 9 square baler

    Hello all. I inherited my grandpa's Massey Ferguson 9 square baler that's been sitting in the barn for over 20 years. As far as I know it was working ok when parked but now everything was rusted up. With the help of a gallon of PB blaster got the plunger unstuck and oiled and greased everything...
  2. V

    Ferguson - Sherman 14a 2 bottom plow

    Hello all. I recently bought a Ferguson -sherman 14a 2 bottom 14 inch plow that looks to be in pretty good shape. It has both coulters and tail wheel and points don't look to bad. I was wondering if someone might have any information about this plow or know where I could get a manual for it? Thanks
  3. V

    Fordson super dexta hydraulic lift questions

    Hello my 63 fordson super dexta would not lift the brush hog high enough unless you take the quadrant rail off and raise further than it would allow. Picks it up all the way if you do. Was told that a cam pin could be worn causing this. I've got the cover assembly off and don't see any obvious...
  4. V

    Fordson super dexta leaking fluid around pto lever

    Hey y'all. Got a super dexta that is leaking fluid from around the pto lever. Looking in the parts book it seems to me that it would be a faulty o ring. But it shows a spring and ball inside there that holds shift lever into position when pto is on. I'm a little Leary of taking this apart to...
  5. V

    Fordson super dexta transmission and rear end fluid specs

    Can anyone tell me the correct fluid for the transmission and rear end of a fordson super dexta? I assume that the lift uses fluid from the rear end. 30w?
  6. V

    Fordson super dexta

    Fordson super dexta transmission and rear end fluid specs
  7. V

    obsolete parts for 40s

    looking for front axle pivot shaft bushings part number M1594T,for jd 40 standard serial number pre 69403.anyone know where some used ones could be sourced? or what original dimensions for these were so new ones could be made? previous owner had replaced front axle pin with a bolt and have found...
  8. V

    jd 40 replacement serial tag

    anybody know where I could find a blank replacement serial number tag for a 40s online? can find for every other model but not for a 40
  9. V

    jd 40 carb. question

    rebuilt carb on my jd 40. it has a marvel tsx 530. runs for about a minute then dies like it is running out of gas. put in complete overhaul kit and made sure all passages were clear. new inlet screen going into carb,new sediment bowl and getting plenty of fuel.adjusted idle adjustment and load...
  10. V

    jd 40 carb rebuild help

    rebuilding carb on my jd 40. has a marvel tsx 530. on throttle shaft my old one had a broken return spring on the shaft near idle adjustment screw and premium rebuild kit came with a spring that looks like might fit but dosent show it on diagram. should it have one or is it for a different type...
  11. V

    rear tine tiller gearbox

    have a Husqvarna 600 crt rear tine tiller that I left out last winter and water got in gearbox and locked shifter up. didn't see any fill or drain ports to drain water out so assuming will have to split gearbox to get freed up. wonder what kind of oil I should put back in it? had one apart...
  12. V

    fuel filter coversion for massey 135

    i was wondering if they make a conversion kit to change fuel filters with glass bowl to screw on type? mine has the double base and i HATE fooling with those darn rubber rings that never seem to fit right. anybody know if they make these for a 135 with double base and if so where i could get...
  13. V

    ford 601 oil pump

    replacing oil pump in my ford 601 tractor. left distributor in and pulled hex shaft out the bottom with pump. planning on replacing the same way. my question is will pump prime on its own? thaught about pulling coil plug boot off and spin it over with starter to see if is going to build...
  14. V

    fuse for fuel gauge question

    adding a fuel gauge to my tractor.all other gauges are manual.should i add an inline fuse to protect gauge and if so what size? it is 12v neg.ground
  15. V

    fuel gauge question

    putting a new fuel sending unit and gauge on massey 135. gauge is pegging full with sending unit attatched or not.should gauge peg with power to it?
  16. V

    mf 135d input shaft seal replacement

    i have a mf 135 diesel tractor with 6 speed dual clutch and losing hydraulic oil out bell housing weep hole. ben letting it go for a while and just parking up hill,but pto clutch has starting to slip when bushhoging in thick grass. not noticed main clutch slipping yet but figure just a matter...
  17. V

    looking for woods rm59 finish mower in east tn

    im looking for a woods rm59 finish mower or compairable for my jd 40 at a fair price if anyone is looking to get rid of one. if so, let me know. thanks
  18. V

    need help finding fuel sending unit for mf 135

    ben trying to find a fuel sending unit for my mf 135 diesel tractor. serial# SDM 641005918 part book calls for 189132m91 unit, but my tank is only 4 3/4'' deep and oem replacements are too tall. guage is for 30-240 ohm. could anyone reccomend where i might find correct sending unit? <img...
  19. V

    will jd 40 handle woods rm59 mower

    will a jd 40 standard handle a woods rm59 finish mower ok? would a over run clutch be necessary?
  20. V

    jd 40 12v conversion

    just baught a jd 40s and previous owner had converted to 12v.everthing seems to work fine except coil is 12v with no internal or external resistor.figure i should cut voltage down for points. should i go with 12v coil with internal resistor or add external one to extend life of points?
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top