(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. D

    Ford 655 not charging until revved up.

    I have a new alternator on my Ford and I noticed the alternator will not start charging unless I rev it really high after that it will charge at low idle. Tachometer also will not work unless I rev it high but once I rev it all is good even at idle. What could possibly be the issue here?
  2. D

    Ford 5000 remotes

    I have a remote cylinder on my 5000 with no hoses. Can someone direct me to a link where I can get just the hoses and possibly the bracket for the rear? I could go to the hydraulic hose shop but I'm not sure about length TPI Etc. I really need these ASAP thanks
  3. D

    655D batteries temperature sensor.

    Hey is there any way to bypass the battery temperature sensor on this Ford? Do you know what the ohm readings should be at 80 Fahrenheit? Thanks guys
  4. D

    268 injection timing help...

    Hello everyone I rebuilt a 95 New Holland 268 engine I now have 50 hours and it's still hazing at idle with unburnt fuel. The book was very vague on timing the pump. What I did was used a dial indicator got the #1 on top dead center lined up all my gears and installed the injector pump with the...
  5. D

    655d sheared oil pump.

    I have been Building engines a long time and I have never seen this happen. I'm just lucky I caught it in time.
  6. D

    655 bad hydraulic noises

    Hey guys my first time getting to use the backhoe since I bought it and done a lot of work on it. The hydraulics in the rear or making an awful noise a little slow and jerky as if it has air. I just rebuilt the boom cylinder but all the cylinders are making that noise. I can't figure out what it...
  7. D

    Ford lift cylinder rebuild

    Hey guys it looks like I'm having to rebuild everything on this 655d because it was literally running to the dirt. I was looking to get a kit for my lift cylinder and I'm not sure if it's a HED or a non-hed. Do you guys know the abbreviation of HED?
  8. D

    Ford 655d question.

    This is my first torque converter transmission so when I'm at idle and put the shuttle shifter in forward or reverse at idle it starts pulling is this normal? I would think when you give it fuel it will start to pull. This post was edited by dannyidp on 09/14/2023 at 04:52 am.
  9. D

    Bsd444 268 655d oil pressure.

    I completely rebuilt my engine I purchased a used crankshaft standard I had it checked I have .003 thousands clearance which the book says 2.2 to 4.8 but it's according if you have a red crank or a blue crank which I do not know. My oil pressure was 22 at idle and 65 at high RPM so I knew...
  10. D

    Ford 655d engineering issue?

    I'm very curious if there was an engineering issue with the steering cylinder on the 655d? I know they only had that cylinder for a couple of years and it seems no matter how you run the hydraulic hoses with the flex of the front axle it either gets into the PTO shaft the fan or the pulley. It...
  11. D

    Ford 655d 90% of the wires are unplugged or cut

    Hi guys I'm almost ready to put a new engine in this backhoe but like I stated 90% of the wires are unplugged or cut. I wonder if anyone in here knows where the wires go from the button on the loader and or the button on the transmission shifter that place is the solenoids in neutral? Thanks...
  12. D

    Ford torque converter rebuild

    Does anyone know a good place to send a Ford torque converter to have it rebuilt? I was told it could be done for less than half the price of a new remanufactured torque converter but I'm not sure who does that.
  13. D

    Ford 94 268 no mark on the crankshaft gear for the balan

    Hey guys I finally got my bearings straightened out. Now I'm putting the engine together and there is no mark on either side of the crankshaft gear for the balance housing gear to line up with. So for now I have it on top dead center I lined up the two marks on the balance shaft gears and set...
  14. D

    Ford 268 balance shaft no marks on the crank gear.

    Hey guys I'm finally getting this engine back together after getting the right bearings. I have the engine on TDC ready to install the balance shaft gears but there's not a mark on the flywheel teeth on either crankshaft the old one or the new one front or back. Could someone please tell me...
  15. D

    Ford 655d 268 crankshaft locking up.

    I've taking this block and had sleeves put in they checked the line bore said it was good polished the crank but when I go to Tighten number three with the thrust bearing it locks down with no end play. I'm guessing I've got a bad set of bearings it is standard. Anybody know what's going on?
  16. D

    Ford 655d 555 Etc

    Does anyone know if the boom on a 655d has the same pin diameter and length as a 555 a e d etc thanks
  17. D

    Best place to purchase engine kits.

    Hi guys on this 268 Ford engine in your opinion where is the best place to purchase a quality rebuild kit? Thanks
  18. D

    Ford 268 piston height issue!

    purchased a Ford backhoe with a spun rod bearing I've got the engine out the piston is sticking out of the block 12 thousands I've got it down at the Machine Shop the where on the cylinders is 3 thousands they will not bore this block due to pin holes so the only other option is sleeves and then...
  19. D

    Ford 268 piston height issua.

    Hi guys I purchased a Ford backhoe with a spun rod bearing I've got the engine out the piston is sticking out of the block 12 thousands I've got it down at the Machine Shop the where on the cylinders is 3 thousands they will not bore this block due to pin holes so the only other option is...
  20. D

    95 655d backhoe question.

    Hi guys I sold my John Deere and just purchased a 655d Ford that needs a lot of work so it will probably be another restoration project like the 5000 Ford project. My question what's the proper transmission fluid and does it mix with the rear end? I haven't got it home yet so I'm not sure. It's...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top