(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. J

    John Deere 310SG backhoe attachment deminsions

    I found a used rock hammer that has 14" pin holes on center for the bucket attachment. I understand that the JD 310sg has 12" centers. I am curious if the 14" pins would fit? The hammer I am looking at is a OKB 304. The specs for this hammer says it is for a 10k - 16k Carrier rating??? It...
  2. J

    Mf40 front loader hydraulic lever seized.

    I noticed the lever that raises and lowers the bucket has seized. It will not budge even after hitting it lightly with a hammer. How do I fix it?
  3. J

    MF52 Swing Cylinder

    Can someone help me identify my swing cylinder on my MF52 Backhoe. It does not look like a cessna model and I am needing to replace the seals.
  4. J

    MF52 backhoe

    I recently acquired a MF52 Backhoe attachment and attached it to my MF40 with a MF34 Fri t loader on it. The swing cylinder is not holding position and is inconsistent with pressure in either direction. I checked the main relief valve and had 1500psi. All the other functions worked well...
  5. J

    Checking MF52 backhoe hydraulic pressure

    I recently installed a MF52 backhoe to my MF34 Front loader on my MF40 Industrial. I want to make sure the backhoe is getting adequate hydraulic pressure. Do I perform this pressure test from the control valve test port on the front loader or somewhere on the backhoe? If from the front...
  6. J

    MF34 Front Loader Filter

    I am wanting to inspect the hydraulic oil filter on my MF34 front loader. I am curious how much hydraulic fluid should I expect to lose if I inspect the filter iif the fluid current level is full?
  7. J

    MF34 Loader Dip Stick Missing

    I found a old post in the forum giving the measurements of the dip stick for the MF34 loader. The post stated that the dipstick was 11 3/4" from the bottom of the breather housing to the full mark. 13 3/4" from the bottom of the breather housing to the "add or low" mark. I am curious what...
  8. J

    MF34 Loader Control valve hose removal procedure

    What tool is needed to remove the 1/2" pipe plug on the loader control valve as indicated "1" in picture. Also, what is the purpose of the procedure if the hose is removed from the loader control valve, then that port is to be plugged, remove the 1/2" pipe plug, then reinstall the 1/2" pipe plug?
  9. J

    MF 52/212 Backhoe

    Is the top hydraulic line or the bottom hydraulic line the hydraulic input on and MF52/212 backhoe?
  10. J

    MF34 Loader

    I am needing the measurement of the width of square tubing on the MF 34 Loader side frame. It is where the sill of a backhoe arm attaches. I am obviously not close to My tractor to measure myself.
  11. J

    MF40 backhoe attachment

    I found a possible for for my MF40 Industrial. Seller will take $1750 and says it has a little slack drone side to side and that the bracket that holds one of the arms up broke and needs to be welded back on. First, can anyone confirm that this attachment will bolt on without modifications...
  12. J

    Backhoe removal and install procedure.

    There is a backhoe attachment installed 5hrs away from me on a MF40 Industrial that I am wanting to remove and install on my MF40 Industrial. Before making the trip, what are the things I need to inspect on the backhoe if the tractor is not working or if I can get it started? Also, what is...
  13. J

    MF 40 rear wheel ballast

    How much does this wheel ballast weigh on my Industrial MF40? I did not realize it was bolted onto the rim when removing the rear tire. I am going to have a good time putting it back on the rim! Also, I am curious if I need to have my rear tires filled with water? I was in the process of...
  14. J

    MF 40 Industrial Fuel Line sleeve

    I am needing to replace a fuel line sleeve on my MF 40 Industrial. It is the sleeve that is for the fuel line running from the fuel filter to the carburator. I am looking where to purchase some and the correct size.
  15. J

    MF40 backhoe attachment

    I am looking for a backhoe attachment for my industrial MF40 and was wondering what my options are and where I can find one in Texas? Thank you
  16. J

    Re: MF34 loader bucket teeth

    I am not able to find the parts and called a MF distributor and they said it is discontinued with no replacement part. Are there teeth I can use for the bucket? As for the bucket blade, apparently there is one in Canada. Is there an alternate balde that will work? MF mentioned that he has...
  17. J

    Re: MF40 brakes

    Sorry, I was replying to another post.
  18. J

    MF40 fuel filter replacement

    I am wanting to replace the fuel filter on my Massey ferguson 40 Industrial. Is it simply unscrew and replace or will I need to go trough the process of getting air out of the fuel lines? Thank you
  19. J

    MF40 brake adjustment

    Currently my MF40 brakes do not work until fully depressed. Operators manual says to adjust the adjustment nut with 1 -3/4 and 2-3/4 free travel. Currently the nut is really tight. To fix my problem of not having brakes engage until fully depressed so I tighten or loosen nut? How do I...
  20. J

    MF40 Industrial seems weak

    I just picked up a MF40 Industrial with me engine rebuild (3hrs). This is my first tractor and I purchased it to be able to clear parts of my property. I am experiencing loss of power going up steep 45 degree hill. Meaning that with full throttle the tractor came to a stop on the hill...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top