-
K
Ford 1920 4x4 backhoe mounting brackets
Hi all, I have a 1920 that I picked up an old Brantly backhoe for. I know that the 1920 used the 758 hoe but can't find anything that shows the mounting bracket set up for mounting it to the tractor. This hoe looks to have mounted to the three-point pins on the rearend and has two standup... -
K
Ford 1920 with bush hog loader 2400qt major fluid restriction?
Hi Folks, I just picked up a Ford 1920 with loader and trying to figure out the loader problem. The 1920 has a strange set up with a diverter valve under the tractor that sends fluid to a loader or what ever and turned the other way it supplies the three point hitch. When I turn the valve... -
K
series 1 td6 starter drive
Hi folks, I know there have been talks in the past on this, but hope that someone has new answers. My td6 starter drive is spinning past again, I have pulled in apart twice and worked on it but think this is the end. Has anyone come up with one that will work on the old series one (1949)? I...- kz1000
- Thread
- Replies: 10
- Forum: Crawlers, Loaders, Dozers and Backhoes
-
K
Ford 601 differential numbers
Hi, I have a rear end housing that I thought was for a 601, but the pinion shaft spline is wrong I think. Casting number on it is 310447 any clue what it fits? Thanks for looking. -
K
Ford 420 injector not seating?
Hi Guys, I seem to have a unique problem that I am dealing with. I Just did a compression test on a 420 and the rear cylinder was low, after further exam I found that I was not seating tight. I am using a fuel injector from that tractor as a compression checker. I installed the regular... -
K
Ford 420 industrial backhoe timing problem.
Hi folks! I picked up an old 420 diesel that runs like crap, no power and really hard to start. I had the injector pump rebuilt, new injectors and no change. I pulled the injector pump cover and #1 injector, put it on tdc compression stroke and the 3 is not lining up with the dotted tooth, it... -
K
Ford 641 workmaster differential ring gear part number
Hi Folks, I picked up a 641 with a bad ring gear and pinion and was wondering if anyone could give me some part numbers and or maybe a list of tractors that would have the same ring in them. With every thing that is on the web these days I can't seem to find a thing for parts numbers. -
K
Ford 861 parts
Hi Folks, I picked up a 861 that had a clutch issue and was surprised when I split it apart. In the bell housing I found a large spring floating around that has nothing to do with the tractor, it looks like a four x 11/4 valve spring. It has beat the heck out of the pressure plate and broke... -
K
after market spindle bushing kit
Hi Folks, Just got around to joining and have a quick question. I bought an after market bearing and bushing kit for my 8n and the id of the bearing is about .050 larger that the bearing that I took off. Did the 8n come with a shoulder that the bearing would ride on in some cases or is this...- kz1000
- Thread
- Replies: 0
- Forum: Ford 9N, 2N & 8N
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy