(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. S

    Presure Plate Fingers on Cub

    What is the measurement I should be looking for on the fingers of a pressure plate for a Farmall Cub??? Mine right now are measuring 7/8". This is a 1948 Cub.
  2. S

    Throw Out Bearing for Cub

    Does anyone have a cross reference number for the throw-out bearing for the Farmall Cubs. Everyone is saying NAPA has them, but NAPA doesn't have the info in their system to look it up.... Thanks Much Steve
  3. S

    Farmall Cub Clutch

    Ok guys my Cub decided toady that it was not going to let me put it into gear. When I step on the clutch pedal it will not go in far enough to let me put the tractor into any gear. I can tell it is close to letting me but it will not. I put a new throw-out bearing in about 3 years ago and when I...
  4. S

    Timing a Farmall H

    How do you time an H with a timing light or do you???? I looked in my operators manual and it has some way that I have never heard of doing, and seams like a lot of steps. Has anyone here timed one with a timing light, and how??? Thanks Steve
  5. S

    Farmall H hard to start

    My H is the pits to start after the engine is warm. Like if you are working with it and have to stop and turn it off it just does not want to turn over. It just turns very slowly like a dead battery. If I let it cool down about 10 min it will turn over and start up. If I jump it with 12 volts it...
  6. S

    Ford Dearborn 14-16 Scikle bar mower

    When using a ford dearborn 14-16 sicklebar mowers do they have to rest on the ground, or can you raise the 3 point hitch and cut about a foot of the ground with the sickle bar suspended???? Steve
  7. S

    Ford Dearborn 14-16 mower

    Can you cut small brush/willow the size of your finger or a pencil from trails with a Ford Dearborn 14-16 mower? Did not know if it works like a big set of hedge clippers or not??? Thanks Steve
  8. S

    Farmall Cub

    Today I went to start the CUB and it cranked just fine but it was making a noise and the clutch peddle was moving back and forth a little. I also was not able to get it into gear, because of the gears would grind if I tried. I am assuming it is the throw-out berring. Question is do I have to...
  9. S

    Farmall H seat shock

    Where can you get the shock for the bottom of a farmall H seat. I brought the old shock to NAPA and they could not match it to anything they had. Is this shock a specialty thing for just seats or can you match it to something else these days Thanks Steve
  10. S

    Carbs on Farmall H

    Are the carbs for the kerosene run engines the same as the gas engines? Will one work as well on either tractor?
  11. S

    Farmall H staying running when cold

    I have an H that is very hard to make it stay running when you first crank it up. I have to constantly pull the choke in and out for about 15 min before it will stay running. After that it is ok. I did run a compression test. Starting from the front of the engine the first cylinder is 70 psi.# 2...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top