(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. H

    Ford 101 Coulters

    I am looking for the coulters and mounting brackets for a Ford 3 bottom 14" Model 101 plow. Do I need to find Ford coulters or will most brands fit? Any tips on where to find them in Wisconsin? Thanks for your help, DJ
  2. A

    Is there a o-ring type lift piston for a 65?

    Been working on my 65 Massey Ferguson. Was wondering is there a lift piston available for this tractor that has an oring on the lift piston instead of the three steel rings? Have found several other models that have new style pistons available but not a 65.
  3. W

    rules

    The best way as it was stated earlier is to police the MPH and that in turn will limit the RPM and to a degree keep the playing feild level. Most (obviously not all) but most puller who have the money in the big motors did so to go fast so mph keeps everyone will they belong. However, if you...
  4. W

    How to make Super H pull

    Email me for info. Pulled super H from 3500 up to 10,000 lbs. Granted I have a low/low but I can give you a couple quick tricks to be up near the top.
  5. W

    Best full cut tire for pulling

    just click the send email button on the right!
  6. W

    Best full cut tire for pulling

    I have a set of 18.4x38 Firestones 151 F&R that would make perfect tires to cut also have a pair of armstrongs. email is open.]!
  7. W

    Butler Farmshow Farmstock mph???????

    If you read the fair book, the pure stock class is running close to division II with the exception of 15.5 x 38 tires are legal down to 4500 lbs class. No cuts allowed in pure stock. As far as the speed limits I know that last year, pure stock was 3 mph and hot stock was 5 mph. Whether that...
  8. W

    July 1-7 pulls in OH, MI, PA or IN

    Are they using the WPTTPA Rules or is the group renting the sled using their own rules? Email is open this time!
  9. W

    July 1-7 pulls in OH, MI, PA or IN

    Is that pull put on by the blue mack or the lawerence county club? Can you email me rules please?
  10. W

    Copper head gasket

    Lubbrick's Gaskets in Lubbrick Texas, you tell him how thin/thick. Nice guy to work with!
  11. W

    Gettin back into it

    I have a farmall H with M&W 9speed. Lots of aluminum. Tractor weighs 3100 lbs empty with pressed steel 15.5 x 38s. I need to sell the tractor to help pay for a wedding. Email is open asking $1975.00 will consider offers and even have 20ft bumper pull trailer too.
  12. W

    farmall M

    I am no Farmall expert, so take this with a grain of salt, but I was told that the standard M motor without the sleeve will accept a piston from a 656. Can anyone verify that claim?
  13. W

    M or 560

    Not sure where you plan to pull, but keep in mind in most clubs a 560 can not pull due to production era. So in that case i would build the M so you could pull anitque, open, farm stock, whatever
  14. W

    Oliver super 77 crank

    I dont mean to knock this idea, in fact I have wondered the same thing, so then me question is the cost of offset grinding worth the 1/2" or so of stroke you gain? Or is there a more cost effective way to gain HP? Believe me I know that in pulling and motor building nothing comes cheap, just...
  15. W

    BLOCK!!!!

    Might try dale reesman in western pa, he ships to midwest pretty cheap. 724-495-7172, he is pretty sharp on ford and farmall. I would call for a price and ask him his opinion same time.
  16. W

    Lawerence County PA, Rules

    Can someone please email a copy of the rules used at Lawerence County. Any help greatly appreciated.
  17. W

    Allis Wc

    I have two complete, 1 parts, and one with pressed steel rear end. Email is open.
  18. W

    Stuck Engine

    If you have the time, taking an old spark plug knock out the ceramic and tread the base to accept an air fitting. Then with an inline pressure gauge, to make sure you dont do more harm than good, I used compressed air to help break her free. Works pretty good, if you do the mass its area =...
  19. W

    h farmall block

    Have either complete block, or running engine in western pa. email is open!
  20. W

    H weigt class

    I have an 48 H with M&W 9 speed, pressed steel 15.5 x 38s weight 3100 lbs with a 150 lbs driver. Nothing extreme has been done, has starter, all the gears, battery on board, actually fuel tank, pto, etc... If you know where to look you can find the nickel and dime pounds to get the tractor down...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top