(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. K

    ZB front end change

    How hard would it be to change a tricycle front end to an adjustable Wide front end on a 1953 ZB? Also, How hard are they to find? Thanks for any information.
  2. K

    Removing 3.152 engine

    Hey minor09, You were right. I finally found the bolt that held the starter on went through the starter, then the engine block. and threaded into the bell housing. As soon as I took the starter off the engine and transmission came apart just as I expected them to do. Thanks for your input. I...
  3. K

    Removing 3.152 engine

    I have started to remove the 3.152 3 cylinder gas engine from my 1974 mf 135. From what I can see everything is disconnected and ready to come a part. I'm having trouble getting the engine to come a part from the transmission. Is there something that I could be missing? It looks like I have all...
  4. K

    Parts

    Could someone suggest a place to buy an overhaul kit for a 1974 MF135 with a Perkins 152 gas engine? Maybe parts of any kind for that tractor. Thanks in advance for your help.
  5. K

    heat shield for MF 135 with Perkins 3 cylinder gas

    I too would like to see a picture of a heat shield for a 135 3 cyl. gas. When mine gets good and warm it will just dies as if the switch was shut off. After it sits for a few minutes it will run again until it gets too warm again. Thanks in advance.
  6. K

    Top radiator hose

    I don't believe you would need to take the fuel tank off to replace the radiator hose. I also think if you would lubricate the hose it would go on easier. I have that same tractor and I've had the fuel tank off twice. There is a bolt on the front right hand side as well. If you'd like to e mail...
  7. K

    Z steering wheel

    I found one. Thanks for the reply. If something happens I'll get back to you.
  8. K

    Z steering wheel

    I'm having trouble finding a cast steering wheel for a M&M Z. Does anyone know where I might find one? Thanks
  9. K

    zb mm hydraulics

    I have a couple hyd. pumps and 2 or 3 tanks, and I think I have a set of steel lines that go to the back. I bought a ZB a while back and these extra parts came with it. I live in south central Kansas if it's not too far.
  10. K

    MM tumble Bug Plow

    Does anyone know if there are new springs available? They look to be in bad shape. I will continue to work on the latches. They are still not easy to move. Thanks
  11. K

    MM tumble Bug Plow

    I am hoping someone can give me some ideas about how to get my plow to lock in the up position when I pull the rope at the end of a the field. Right now it will turn over but will go on over to the plowing position going the other way. I know very little about it and it has been sitting quite a...
  12. K

    ZTU Radiator

    Thanks for all the suggestions. Yes the mix in the radiator is a 50/50 mix. I'll look at all the other things and make a reply when I find the problem. Thanks again.
  13. K

    ZTU Radiator

    What degree thermostat should be in this tractor?
  14. K

    ZTU Radiator

    I have a 1944 ztu. When I run it long enough to get good and warm, not hot, the radiator looses coolant out of the overflow shortly after I shut it off. It runs good other than that. Does someone have an idea as to what might be causing this. Also is this a pressurized system. There is never...
  15. K

    MF 135 misses at high rpm

    After changing the condenser, coil, and fuel line it seems to have corrected the problem. I had tried a used condenser and coil that I had but had no success. Finally got new parts all at the same time so I don't know for sure what fixed the problem. Thanks to everyone for their suggestions.
  16. K

    MF 135 misses at high rpm

    I have a 1974 Mf135 3 cyl. Perkins gas. It runs great below 1500 rpm. Above there it sometimes misses and backfires to the point it will die. Maybe next time I start it , it will run fine. Problem is intermittant. I've tuned it up and have gone thru the carb. I'm clear out of ideas and...
  17. K

    1969 MF135 Perkins Gas

    I have a 74 MF135 that does about the same thing. It runs great up to 1500 RPM but above there it misses and backfires. I've been thru the carb. and tuned it up. Starts good and runs good at low RPM. Would like some ideas also. Thanks
  18. K

    Running rough

    I think the tank is pretty clean. I'll check the screen. I also have a new temp gauge and sending unit. Just haven't taken time to put it on. You're right. That needs done right away. I used the tractor last night with no problem but it wasn't pulling as hard as it was when it started missing...
  19. K

    Running rough

    I have a 2-70 white with the 283 diesel. After running it about 3 hrs. it started missing and running rough. Also there was some gray smoke coming from the exhaust. I let it cool off and then I changed the fuel filter. It ran fine after that. I wouldn't be concerned except this has happened 2 or...
  20. K

    cylinder sleeves

    I'm in the process of making a puller to remove the sleeves from my 1961 601 workmaster. This engine is the 134 cubic inch. Could someone please tell me the diameter of the bore in the block or the wall thickness of the sleeve? This is the first time to overhaul one myself. Thanks in advance.
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top