(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. M

    Pto doesnt disengage mf 253

    Spins freely with engine off I am thinking when you disengage there is pressure put on that arm that touches that brake disk I am going to check and see if I have any or enough pressure for that
  2. M

    Pto doesnt disengage mf 253

    My 253 massey pto doesnt engage. When using a rotary cutter it doesnt spin but when hooked to a hay rake it will spin slowly when lever is in disengaged position. With tractor idling it spins and cant stop it with a gloved hand. With tractor off shaft spins freely. My service manual shows a...
  3. M

    348 sq baler

    Thanks
  4. M

    348 sq baler

    I have a John Deere 348 square baler and have a 30 bale kicker. Will this kicker fit this baler, or is it to much modifying to make it fit ? Thanks in advance.
  5. M

    Hagie 647 owners manual

    Does anyone know where I can get a manual for a hagie 647 sprayer? I did find a parts manual but I cant find a owners manual anywhere. Thanks Im advance.
  6. M

    Help identifying this sprayer

    Maybe
  7. M

    Help identifying this sprayer

    I having trouble uploading a picture
  8. M

    Help identifying this sprayer

    I just purchased this sprayer from the local university and hoped some one could tell me a little about it. Model and so forth.
  9. M

    253 mf hydraulic leak

    I have a massy 253 that has a hydraulic leak coming from the inspection cover. I have tried to repair it a couple times. First time just a seal and it still leaked. Second time I replaced input shaft bearings and seals. Ran a hour then started to drip and then got worse. Last time I replace...
  10. M

    Reekie reliance 500

    I just purchased a reliance 500 destoner and am trying to locate a operators manual. Can anyone point me in the right direction to find one I have googled it but no luck. Thanks in advance
  11. M

    Jd 3950 decals

    No sir ,I didn’t ,rookie mistake I guess but could probably get some I have a friend with one not to far from me. Do you have to get measurements also with the pictures?
  12. M

    Jd 3950 decals

    No sir ,I didn’t ,rookie mistake I guess but could probably get some I have a friend with one not to far from me. Do you have to get measurements also with the pictures?
  13. M

    Jd 3950 decals

    I repainted my chopper and didn?t tape up what few decals were left and now the decals are discontinued from jd or most of them with the exception of the generic warnings Has anyone else had trouble finding decals and if so did you find anyone to make them. Most of the people around that could...
  14. M

    Komatsu d38-p trans temp gauge

    I have a Komatsu d38-p dozer and my trans temp gauge has quit. Replace sending unit, checked for broken or chewed wires and nothing. So I contacted Komatsu and they say my gauge is discontinued cause machine is so old. Does anyone know of someone that can fix/rebuild this gauge? I live in...
  15. M

    Jd 3950 chopper hyd valve

    I purchased a jd 3950 and it was pulled by a 1135 massey and I am using a jd 7330 and I looked in the manual about changing from a open system to a closed system and I do not have the red screw the manual talks about using and wondered what I needed to do Go back to jd or if someone had done...
  16. M

    Charge pump 1135 massey

    I am in need of a charge pump for my massey 1135 and am wondering where to go for it I really just need housing but figuring I will have to bite the bullet and buy a rebuilt one Who do y?all recommend on this purchase Thanks for the info
  17. M

    Trans fluid over full on a 1135

    I just purchased a 1135 that has no steering and no hydraulics so I started with filter and so on When I drained the oil from the plug at the pickup pump not much in it maybe 2-3 qts but my dipstick is over full by the battery Do I have a channel or hole that?s plugged and not allowing the...
  18. M

    7330 hard starting

    Since I serviced my 7330 it has been hard to start after sitting overnight takes about 15-18 seconds for it to start If you shut it down for a second or an hour it starts right back up maybe 2-3 seconds Temp doesn?t seem to affect it Like it?s losing prime Fuel filters are not wet like they...
  19. M

    Cat 205 LC excavator

    Does anyone here have any comments or input on a cat 205 lc excavator This one has the Perkins diesel in it not the deutz I thinks it around 28-30000 lbs Thanks in advance
  20. M

    Wide jd chopper head to a narrow head

    I saw a ad for a wide John Deere chopper head that the dealer would cut down to a narrow row head Has any one ever done this if so how involved is it they told me it would take a half day to get it ready to go to the field
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top