(800) 853-2651
SHOP NOW

Search results

  1. W

    Fuel Guage o M7030

    My fuel gauge works part of the time. Right now it seems to be stuck on 1/2 tank. How much of a job to replace or repair? Or do I stick with the stick?
  2. W

    Series 420

    It is time to replace our JD 420. It is used for mowing our Rod and Gun Club (6ft finish mower). 2-3 acres once a week. Everything works except the charging system. I have a feeling it is the wiring to the generator or regulator(we keep the battery charged). It is housed and starts the first...
  3. W

    Allis Chalmers 3 bottom Roll-Over Plow

    I have found an Allis 3 bottom Roll-over plow that looks to be in good shape. Points, lands, shins look good in the pictures. It has a hyd. powered roll over. Frame looks very similar to a regular Allis 3 bottom plow.(I have one) I have not looked at the plow and I think it may be in an...
  4. W

    Snow Plow for Euro-Global Receiver

    What is the easiest/cheapest way to mount a snow plow on my euro-global FEL receiver?
  5. W

    Is it True? Milwaukee and Ryobi made in same factory.

    Just saw this online so it must be true!
  6. W

    Roll-Over 2 Bottom Plow

    I keep looking for a 2 bottom 16 inch roll-over plow. Any I have found are too well used. Any suggestions?
  7. W

    Replacement pads for vise

    This is a small bench vise with 3 inch jaws. The hardened pads have been removed and lost. I have looked on Amazon and they are not cheap and don't tell the distance between screw holes. Mine is 2.5 inches and no idea what the thread is. Where do I look for replacements?
  8. W

    Food Plot Drill

    I mix cereal grain with my pelleted lime of fertilizer and spread with a cyclone 3 point seeder. I spread brassica and clover seed with a belly grinder. Maybe 2-3 acres a year. I am not getting uniform coverage. Keep thinking I need a Brillion Drill, but the price is prohibitive. I...
  9. W

    Broke the loader joystick

    10 degrees yesterday and son decided to move a wood pile. Joystick would not tilt the bucket, up and down were fine. There was a little play and I kept forcing till I broke the plastic threads. It did finally start working after a half hour. Was there moisture in the fluid and the valves...
  10. W

    Generator exhaust

    My 10KW portable generator has a spark arrestor and I was reading how to clean it. Appears to be as if a pipe fitting could be fabricated and attached and you could exhaust it through a wall. I store the generator in the non attached garage and when I run it I exhaust it through the open...
  11. W

    Seafoam and K-Mule

    We have a 2010 K-Mule, it was the first fuel injected model. When it runs right it is great BUT, sometimes it just will not idle. Let off the gas and it quits. Always re-starts if you let the electric fuel pump catch up. That's the secret, turn the key on and listen for the fuel pump to stop...
  12. W

    JD 420 Steering

    The steering is very loose in our old JD 420 with the power steering pump on the fan belt. Steering wheel to pump is tight, and the tie rods are tight. So, the half turn of slop is in the steering column/power steering unit someplace. I have looked for an eccentric or screw adjustment but...
  13. W

    Plumbing FEL

    Our old Kubota M7030 has a Quckie FEL that is powered through one set of remotes and you have to hold the handle back for it to work and then the 3 point and the other set of remotes won't work. There is a suction line and a delivery pipe running from the pump to the hyd connection at rear of...
  14. W

    JD 420 Starter

    Our old 420 failed to start yesterday. The starter motor is running but it doesn't engage the flywheel. My I&T shop manual doesn't tell me anything. Is it a normal Bendix or did the JD engineers do something different? Will the starter come off without removing the toolbox, not much room...
  15. W

    Farmi Wench Synthetic Rope and Clutch

    What did you do before putting Synthetic Rope on a Farmi type wench? I understand you have to polish all the pulleys and the drum so it doesn't snag. Is there a source of parts for the Farmi, our clutch is about shot.
  16. W

    Electrical Question

    Going to buy a 30Amp generator and set it up to run the house. Have a 40 amp sub box in our garage and I want to run through that. I understand there is a special lock out receptacle, so you won't feed back into the service line. And an extension cord with receptacles available. Is there a...
  17. W

    Portable Welder

    My old tombstone is old! And I need a bigger generator. Am I shooting myself in the foot considering a portable welder to replace both? What do I look for and how does a DC welder convert to an AC generator?
  18. W

    Cordless Impact Wrench

    I have a Ryobi brushless 1/2 inch. CHEAP All my equipment is old and junk. Rusted 1 inch bolt, been putting ATF/Acetone on the threads for a week. 3/4 socket set with a 3 foot helper and the nut just started. Put the Impact on it and it hammered for 2-3 seconds and the nut started and came...
  19. W

    Stubborn Hydrulic Fitting.

    I am sure this is a NPT into the cylinder but I can't get it out. Metric open end fits tightly and even with a helper I am afraid I'll make the fitting round. Any ideas how to get it started?
  20. W

    Dual Fuel Generator

    Leaping over dollar bills to save small change! How do you switch fuels on the Dual Fuel generators? Can you do it while it is running? Or, are there some adjustments that must be made? If the grid goes down, fuel will not be available.... no way to pump or deliver it. 250 gallons of LP is...
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top