(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. B

    IH 184 MOWER SWAP

    I have two IH 184 tractors. Tractor 1 has the 3-point hitch with a Woods mower. Tractor 2 has no 3-point hitch and an IH 3160A mower. The IH mower on tractor 2 is in excellent condition but the tractor needs work. The Woods mower on tractor 1 is rusted through but the tractor is excellent...
  2. B

    2000 New Holland TN75D repair

    I sheared off the two studs that anchor the front of the loader frame to the tractor bolster. I am terrible with metric. What exact size are the bolts and thread pitch that screw into that front bolster? I think I will need to heli-coil for repair?
  3. B

    New Holland TN75D No Shuttle

    Getting two different error codes. Code 48-no forward or reverse. Code 39-No reverse but forward works. I cannot find a listing of error codes in my service manuals? What are these two codes for? Where in the manuals do you find error codes?
  4. B

    Location of NH tranny pressure sensor

    2000 NH TN75D I think I may have pulled a wire or had a bad connector to the tranny pressure sensor. Shuttle intemittantly does not engage. However, no idea where that is located. Help needed to locate.
  5. B

    New Holland TN75D No Shuttle

    I was grubbing out trees when this all started. Might have pulled the connector to the trans pressure sensor. Where do I look to find it? This post was edited by buckbored on 12/03/2021 at 06:47 pm.
  6. B

    New Holland TN75D No Shuttle

    Thank you. Didn't know about the blink count!
  7. B

    New Holland TN75D No Shuttle

    2000 New Holland TN75D While working, I suddenly get a shuttle alert icon and the tractor will not move forward or backward. I must completely shut down the engine, wait a minute and then restart. The alert goes away and I have forward and reverse again for a few minutes. Then it goes away...
  8. B

    IH 184 Creeper Needed

    Thank you for the diagram. Looks like the correct unit. Hoping to find someone with a parts tractor willing to remove all the creeper assembly and sell as a unit at a fair price.
  9. B

    IH 184 Creeper Needed

    Restoring a 1978 IH 184 Low Boy. It was purchased new without the creeper option. Since I am rebuilding everything I though I would like to install the creeper setup? Can that be done and if so, what would I need in the way of parts and information? Help appreciated!
  10. B

    Farmall B Rear Wheel Change

    Back several months ago someone posted up photos of a Farmall B with the rear tires and rims converted to a larger truck rim and tire size. I lost the post and would like to contact that person for more information. Anyone remember who it was?
  11. B

    Super B

    I really like the larger tires and rims. How did you marry the larger rims to the B axles? What rims did you use and what size tires are these?
  12. B

    Super B

    Your B is impressive. Cool ride!
  13. B

    Super B

    LOGO ????
  14. B

    Super B

    OK, So I am trapped at home due to the virus. Sitting here thinking of possible projects and it dawned on me that Farmall never made a Super B. Super A and Super C but no Super B. I have a nice B just sitting here. So...just for laughs, what would it take to make my B a Super B? I realize...
  15. B

    Farmall B Steering Shaft U-Joint Replacement

    This is my U-Joint. The is no cap on the knuckles to allow the inner bearing to be removed??
  16. B

    Farmall B Steering Shaft U-Joint Replacement

    Looks like the yokes are white metal? If I heat them and try to open them up I think they are going to snal off??
  17. B

    Farmall B Steering Shaft U-Joint Replacement

    1944 Farmall B The U-Joint in the steering shaft is shot. It looks like this cannot be repaired like other U-joints I am familiar with? Usually there are snap rings that can allow the inner bearing to be replaced, retaining the knuckles. But there are no snap rings on my U-joint. Looks like...
  18. B

    B Carburator repair

    Pretty sure it is carburator. Stops sputtering if choke is pulled partially closed. No fuel filter on line and bowl clean.
  19. B

    B Carburator repair

  20. B

    B Carburator repair

    Time to get to a starving carburator. My '42 B has a Zenith on it now. The tractor starves out under load so I have a problem. Am I better off to just get a full rebuild kit for the old Zenith or should I look at a newer type for full replacement?
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top