(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. G

    1970 JD350B Crawler

    My 350B was not steering correctly either, we pulled the seat and removed both covers where Band adj is made, also the brake steering is adjusted in the same cavities. It must be done in the correct order as well. You can with some good light see the band material thickness. (A inspection cam...
  2. G

    JD350B Electrical Starting Problems

    Sometimes the Dashboard push button starter s/w fails from contact burn. I use a Hot-wire from the old days copied from auto theft guys to test or rule in or out switches or Sol. s/w's. Battery side of coil to Battery = 1 wire, Jumper the Sol Switch =1 more, should crank and start or lead to a...
  3. G

    Problem with YTC's Governor for 8N

    This message is a reply to an archived post by Bruce VA on May 26, 2017 at 18:50:58. The original subject was Re: Problem with YTCs Governor for 8N. I wouldn't bother with a free I&T F04 ANYTHING, the one I paid for years ago called for a .025 Ignition point gap on a 51 8N! The Dwell on a 4...
  4. G

    coolant path diagram for 8N

    As far as my running for Public Office goes JMOR, I'm just way too honest and I would run on the Platform of a Promise to do Nothing for anyone ever. I will Promise to keep that promise, if I were a Politian that is. 😘
  5. G

    coolant path diagram for 8N

    I will agree to the point of either the stream water turns the Grist Mill or the reverse occurs when pumping using stream power to run a smaller pump up hill. A impeller pump with straight or curved impellers can be powered by outside forces. Blow by often does happen when the head pressure...
  6. G

    coolant path diagram for 8N

    Thank you, great photo. I bought a replacement coolant pump, when I examined it the impellers were curved in the opposite direction of the original! So I set out to determine which was correct. In correct rotation in relation to impellor curve both would pump. The correct curve will pump better...
  7. G

    coolant path diagram for 8N

    Would anyone have a cut away or otherwise simple typical diagram of the coolant flow path for an 8N? From the radiator to the coolant pump and distribution to return to radiator. I surly would appreciate it if they exist anywhere to print out.
  8. G

    9N/8N Replacement Distributor shafts

    Tim PloughNman Daley, Thank you, So you know, I did get that NAPA rotor today and when I put in "on" and inverted the assembly toward gravity, the Rotor stayed on all by itself!! Thanks so much for that part information for the rotor. Beyond a magnet on a RPM centrifugal force for advance...
  9. G

    9N/8N Replacement Distributor shafts

    I'll give it try at NAPA then, most anything would be better if it fits snugly. I have not run across one yet and keep shimming the flat. I wished I would have saved the one that did, I probably didn't really need to replace but file a little. Hindsight wisdom.
  10. G

    9N/8N Replacement Distributor shafts

    Let me know if you tried a Magnet yet on just the edge of your weights. Any Iron or steel of any kind a magnet will stick to. Some Stainless steels are also the same way magnetically.
  11. G

    9N/8N Replacement Distributor shafts

    Correct but if the Rotor can freely turn a degree or two on its axis because of sloppy, cheap, fit's who knows what the mechanical cam advance is affecting. The rotor could be doing anything it pleases in relation to the Distributor Cap contacts. Retarding or Advancing when not locked in a...
  12. G

    9N/8N Replacement Distributor shafts

    I guess it would mostly depend upon the allowable air gap tolerance window + & - in a pickup sensor to the cam lobe mags. If spark advance changes with electronic 6v kits as point systems you probably will see a dwell change with bearing slop on a bench test. Just no more point dog wear to deal...
  13. G

    9N/8N Replacement Distributor shafts

    Thank you for the same conclusion, a dirty piece of a non-magnetic alloy "looks" like any other metal. The magnetic test is best. I didn"t really need a spare coil, since it was just a spare. I lent out without hesitation and is gone. Spare small anything is "golden" on these beauties, over...
  14. G

    9N/8N Replacement Distributor shafts

    Tim PloughNman Daley, I wonder have you ever stuck a magnet on these cast cam weights yet? I have a original cast iron shaft assembly myself but the weights are still of aluminum. It weighs more only due to the cast iron shaft alone perhaps?
  15. G

    9N/8N Replacement Distributor shafts

    Farmer Dan, If I had not prior already retrofitted a shiny new foreign part for under $30, and myself being particular as I am about necessity Geometrically and dimensions I would have reached out, but what is done is done. The stuff available for that component part are of no equal to...
  16. G

    9N/8N Replacement Distributor shafts

    For these front mounts, What I"d like to find is a Rotor replacement that actually fits on snugly, they all seem to wobble. I"ll take and shim the flat after I get a caliper dimension of the mating parts. Placing the offset drive key in a vice and turning the Rotor back and forth they have no...
  17. G

    9N/8N Replacement Distributor shafts

    if it help,s my Evaluations: I paid top dollar for a new dist. camshaft assembly, to me high at + $90 and discovered the throw slots, although reversed in the advance were advertised to work the same on the "net". not the package! I was not going to use it after I also obtained another one for...
  18. G

    8N Distributor Timing bolt

    Farmer Dan, Thank You so much for the patient assistance in sending me the parts. They arrived Saturday here. Well boxed. Someone at USPS must think the sorting machine is coming apart if they find the first ones laying around;-) And TY to TOH as well as a first reply. I can finish up the...
  19. G

    N front mount distributor bolt

    Farmer Dan, I received a bubbled envelope today with 2 of your business cards inside only, one end was torn open, about the size of a finger would do and no original 10-32 hex head bolt to hold the backing plate in time position. I only opened it since my wife saw some paper inside and to get...
  20. G

    N front mount distributor bolt

    FarmerDan, my mailing address I sent to your email. That's just really great, TY. George in Mi.
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top