(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. W

    4320 Draw bar pin holder replacemenr

    Thanks, how do you install the new pin, and get it to stay in place?
  2. W

    4320 Draw bar pin holder replacemenr

    Does anyone know how the updated draw bar pin holder works on a 4320? I have looked at the parts break down and I can’t figure it out. New pin is 18.
  3. W

    4320 hydraulics slow

    Not sure what has been done on the tractor. Other than upgrading the batteries and installing something that helps it start better. Needed the Deere item. I spent the last year cleaning all of the dirt and oil from off. Just baby powdered the tractor to find oil leaks. Going to be splitting to...
  4. W

    4320 hydraulics slow

    Used my 4320 yesterday the 3 point is very slow to react, and then will drop down on while turning for my return pass moldboard plowing.
  5. W

    Help 4320 and 630 tractors

    Need some help with my two Deere tractors: 630- lost the gas cap and bought 2 new ones from Deere. the cap continue to leak gas when the front is tossed around. I have replaced the cork gasket multiple times. Any idea on how to stop the gas from spilling out the top? 4320 one of the hydraulic...
  6. W

    John Disc model H1200 trailer disc

    Just uploaded the full disk. Going to try the Amish location in PA.
  7. W

    John Disc model H1200 trailer disc

    I have an older John Deere disc the gang shaft broke, and I want to get a new one. Shaft is 1 1/8” width total length is 61” subtract the threads I am 59”ish. Can anyone help me locate a new shaft? This is the best I have found...
  8. W

    3pt disc disc for 630

  9. W

    3pt disc disc for 630

    Would an 3pt 8ft series 200 dirt dog disc be too big to run behind a 630 John Deere?
  10. W

    Follow up 630 fly wheel leak

    Went back and worked on the 630, and pulled the engine oil filter. There was gas in the engine oil. I changed the automatic shut off washer, is there anything else to replace or fix prior to putting oil back into the tractor and running it again?
  11. W

    Follow up 630 fly wheel leak

    I finally got around to switching out the Oring on the auto shut off carb today, and got to investigate the oil leaking out of the bottom of the fly wheel cover. There were no real visible oil leaks. The oil had pooled some by one of the cover bolts near the back side of the fly wheel cover in...
  12. W

    Rebuilt clutch

    I am currently planning to make some stands to split the tractor and will need to do the pro seals and the other seal know to leak. I found out Deere or the owner of a form Deere dealership will adjust clutch for an hour of shop time. I am working on a 4320
  13. W

    Rebuilt clutch

    Has anyone used an aftermarket rebuilt clutch for a 4020 or 4320? Deere no longer loans out the tools. I would have to purchase the tools Thanks
  14. W

    630 engine oil leaking under fly wheel cover

    Can you send me the link for it?
  15. W

    630 engine oil leaking under fly wheel cover

    Thanks, for the response.
  16. W

    630 engine oil leaking under fly wheel cover

    I got on my 630 and noticed the engine oil pressure was very low. Got down and looked and found oil leaking out of the fly wheel cover. Any idea what would cause this?
  17. W

    630 top link rebuild

    Yes the ball rotates around the bushing
  18. W

    630 top link rebuild

    My top link ball has what I would describe as chatter marks around the John Deere ball and then a sleeve. I purchased the parts needed to rebuild the locking mechanism. Is there anything I need to pay very close attention to?
  19. W

    630 1st reduction casting cracker

    Is there anything with running a brush hog that would cause a binding or mash the gears?
  20. W

    630 1st reduction casting cracker

    I have spent a bunch of time working on the families 630. Last night I got to go look at the 630, my dad some how cracked the bottom portion of the first reduction casting behind the drain plug. My father was running a 6ft bush hog. I can not find any indication of the casting being hit from the...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top