(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. N

    Brake Pawl sizes

    I have a question about the brake pawls on a 1941 Ford 9N. So I've read that the right side brake pawl is larger than the left and that the left side is down and the right side is up. Now I can only find one size on the internet and most of the people talking about the different sizes of...
  2. N

    front steering removal

    Jim thanks this is what I finally did and was able to remove the pin. Then the real fun began to remove the steering arm. Too bad, it's not working for the other side, but maybe it will once I have the weld broken. Thanks Kevin
  3. N

    front steering removal

    Yeah, I've tried it but mine must be made of cast because it's really soft and also is too narrow to fit the spindle top through the middle. I'm sure this would be much easier than beating the snot out of the bad spindle. I'll have to locate a better pickle fork and give it a try. Thanks...
  4. N

    front steering removal

    Yes, this is exactly what I have and I'll need to try to source one pin from someplace. Would you know of a good place where I can pick me up one? Thanks Kevin
  5. N

    front steering removal

    Even without being welded on it took a lot of beating to get it off. Now that I can use the pin that I pulled out to compare with my other side it looks like they either pulled the pin almost all the way through and or put it in wrong. That's why they had to weld it. I'll know more when...
  6. N

    front steering removal

    I have four different parts books and they all show this arm differently. The parts books published after 1942 show it as a bolt with two heads with a split arm, the other parts books published in 1942 and earlier show a locking pin and a solid arm. So somewhere after 1942, the split arm with...
  7. N

    front steering removal

    Yes, there is no head to either bolt so I assume it came with a kingpin wedge bolt from the factory. I have been beating on the bolt to remove it but have had no success I've even tried a large tapered punch with no success. Later today I am going to try some heat to the side the bolt is on as...
  8. N

    front steering removal

    Yes, the grinder is for another day right now...but that's what I've been up against trying to repair my 9N. -Kevin
  9. N

    front steering removal

    Thank You
  10. N

    front steering removal

    Thanks old ... I've been trying to remove the stud or bolt I put the nut back on before I tried to hammer out the bolt I have also tried a large tapered punch to get the bolt to go back through but I have been unsuccessful. I wasn't sure if that bolt came out or not, but I thought it had...
  11. N

    front steering removal

    Thanks Abbby I don't have a torch, but I do have a propane torch to try. Kevin
  12. N

    front steering removal

    I'm trying to remove the steering arms that are on top of the front axle spindles. I've seen videos that say to just pop them off with a hammer, but no matter what hammer I use mine don't move. The one on the right has been welded on but that's for another day my left one will not move. I've...
  13. N

    9N lift cylinder spring

    OH, where were you with this picture when I needed it? LOL, I'm going to save it off so I can use it as a reference for my tractor. Everything I found prior didn't show it this well and that is exactly what mine looks like. Thanks again for these pictures.
  14. N

    Data Plate Removal

    Thanks, I've tried smaller ones, but the ones I have are just breaking. I figured 1/8 would take the rivet out on the first try, but if I have to I might have to try a smaller one first.
  15. N

    Data Plate Removal

    Thank you this will be my last resort. I was hoping to do it right the first time, but that's not going so well so far...
  16. N

    Data Plate Removal

    I've talked to a machine shop and they charge a $150 setup charge, but It wouldn't be the first time I have had to have something done because I goofed it up. Guess I could remove the upper steering housing and take it to them and see what they would charge to redrill these rivets out. I have...
  17. N

    Data Plate Removal

    Thanks I'm going to have to look for some of these nippers at some flee markets so I have a pair just in case my wife lets me do another tractor.
  18. N

    Data Plate Removal

    As you can tell I'm new at this, but the education that I'm getting is priceless. I'll see what I can do and my last resort will be to off-set the data plate. Thanks for your response
  19. N

    Data Plate Removal

    The data plate that was on there was very worn. I have put those tips in the front of my repair manuals for reference.
  20. N

    Data Plate Removal

    Hope someone can help me with this. I have a Data Plate that I removed by removing the heads of the rivets with a chisel. Now that I have the Data Plate removed and just stubs where the rivets go, I've been trying to drill them out with no results except lots of broken 1/8" drill bits...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top