(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. W

    My 180 is about done

    Ok I will message you directly if I can figure out how to 🙂
  2. W

    My 180 is about done

    I get that , lol it can be a pretty deep hole
  3. W

    My 180 is about done

    Nice Job on the restoration, mine is still in its work clothes, but they are great tractors 🙂
  4. W

    Oliver 1550 won't run right. out of things to try

    I I've been following this, how cool is it, all this knowledge willingly shared to help a guy out
  5. W

    Farmall IH 706 Rusted Fuel Tank

    I built a rotisserie on a tilt adjustable table , filled a tank off a massey Ferguson 180 with about 3 lbs of assorted nuts and bolts, and sat in the shop turning a crank, I watched 2 and a half runs of a Christmas story and it was clean enough for me , I triple rinsed it with diesel fuel and...
  6. W

    I did a thing yesterday, now the work starts

    A friend and I tore down his Dad's 28 x 80 dairy barn, we split the lumber and beams and each made different projects, and sold some of it, we were young and barely had enough money to buy beer for the nail pulling that happened at the end of every day, it was a fun project and nobody got hurt...
  7. W

    Old fuel, bad fuel? In a180

    Nice tractor, enjoy👍
  8. W

    Old fuel, bad fuel? In a180

    I had a motor at first but it turned to fast and the time it would have taken to make it right, I figured just turn it by hand and get it over with. The speed wrench brace made it better
  9. W

    Old fuel, bad fuel? In a180

    Here is a picture of the tumbler I built , very crude , but effective
  10. W

    Old fuel, bad fuel? In a180

    Hello All, here is an update if you are interested, most of what I learned is probably common knowledge, however hopefully someone will find this helpful. I drained the fuel tank and removed it, the corrosion was everywhere inside, I built a tumbler, and spent about 4.5 hours slowly turning it...
  11. W

    Perkins 4.236

    Thanks Dieseltec, I will remember that for next time 🙂
  12. W

    Perkins 4.236

    This is interesting, I changed fuel filters on a 180 with a 4-236 Perkins diesel, my hand pump only had pressure for the last 1/4 of lever stroke, is there a relation to the crank position for the hand pump to work better? we had a tough time getting mine running.
  13. W

    A question about Minnesota Massey Ferguson dealers

    Lol, thanks, that very well could be , it replaced a international, 460 or 560 I think, and power wise it was next in line to a 1966 1100
  14. W

    A question about Minnesota Massey Ferguson dealers

    I am working on a 180 that I assumed my parents purchased new in 1973 from a dealer in Lecenter Minnesota. I was 6 years old and I think I remember it being delivered. When I checked the serial number it showed it was a1970 model. There are remnants of 3 dealer tags on it. I assume The...
  15. W

    Canister oil filter for 180

    Yep , oil pressure was 50 so I think I'm good , I will have to watch it probably would not hurt to run it a few hours and then change it. I would guess there was no filtering with that 1188 in there
  16. W

    Canister oil filter for 180

    Thanks I'm going to install the 1183 , I assume the oil pressure is measured after the filter so if my oil pressure is normal I should be ok. Does that seem right?
  17. W

    Canister oil filter for 180

    Thanks I think maybe I need the 1157
  18. W

    Canister oil filter for 180

    Yes it is a 4 cylinder diesel, thanks for the response I am going to install it and watch my oil pressure if is wrong I will have to change it later.
  19. W

    Canister oil filter for 180

    I am changing oil in my 180 I purchased a 1183 oil filter recommended by napa,when I dropped the filter canister it contained a 1188, I pretty sure that is not the correct filter. So my question is, do these pictures look right with the 1183 filter in the canister there is so little room around...
  20. W

    Old fuel, bad fuel? In a180

    Here is a picture of it in a warm shop , I'm happy about that
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top